UT622A Digital Inductance LCR Meter
| Specifications | UT622A | UT622C | UT622E |
| Certificates | CE, RoHS | ||
| Test frequency | 100Hz, 120Hz, 1kHz, 10kHz | 100Hz, 120Hz, 1kHz, 10kHz, 100kHz | 100Hz, 120Hz, 1kHz, 10kHz, 100kHz |
| Test signal level | 0.1Vrms, 0.3Vrms, 1Vrms | ||
| Output impedance | 100Ω | ||
| Measurement parameters | Primary: L/C/R/Z Secondary: D/Q/θ/ESR |
Primary: L/C/R/Z/DCR Secondary: D/Q/θ/ESR | |
| Auto LCR | √ | ||
| Test terminals | Three-terminal test jacks, five-terminal test sockets | ||
| Test rate | Fast (20 times/s), medium (5 times/s), or slow (2 times/s) | ||
| DCR test rate | — | — | Fast (20 times/s), medium (5 times/s), or slow (2 times/s) |
| Ranging mode | Auto/hold | ||
| Tolerance range | 1%~20% | ||
| Testing circuit mode | Series/parallel mode | ||
| Clearing correction | Open/short circuit | ||
| Fuse of test ports | 0.1A/250V | ||
| Communication interface | Mini-USB | ||
| LED alarm for tolerance (pass: green; fail: red) |
√ | √ | √ |
| Display range | |||
| Maximum reading | 99999 | ||
| Minimum resolution | 0.0001 | ||
| Maximum accuracy | 0.001 | ||
| L | 0.00μH~99.999H | ||
| C | 0.00pF~99.999mF | ||
| Z/R | 0.0000Ω~9.9999MΩ | ||
| ESR | 0.0000Ω~999.99Ω | ||
| D | 0.0000~9.9999 | ||
| Q | 0.0000~99999 | ||
| θ | -179.9°~179.9° | ||
| DCR | — | — | 0.01mΩ–20.000MΩ |
| Temperature coefficient | 0.1× (specified accuracy) /°C (0°C~18°C or 28°C~40°C) | ||
| General Characteristics | |||
| Power | 3.7V 1800mAh lithium polymer battery; Input: 220V (1±10%), 50Hz (1±5%); Mini-USB output: 5V, 1A | ||
| Display | 2.8′ TFT LCD 320X240 | ||
| Product net weight | 420g | ||
| Product size | 93mm x 192mm x 44mm | ||
| Standard accessories | Short circuit board (UTR-001), USB cable, 5V 1A power adapter, Four-terminal Kelvin testleads (UTR-L100k-H) (UT622C/E), Alligator clip test leads with rubber plugs (UTR-002)(UT622A), English manual | ||
₨57,410
CompareUT622A Digital Inductance LCR Meter
Precision LCR Meter – Up to 0.1% high accuracy measurements, the unit mainly measures inductance (L), capacitance (C), resistance (R) of components, also measures impedance (Z), dissipation factor (D), quality factor (Q), angle phase (θ), and ESR.
Accurate Measurement – Selectable 4 test frequencies of 100Hz, 120Hz, 1kHz, and 10kHz. Selectable 3 test levels of 0.1V, 0.3V, and 1V. Selectable tolerance of 1%, 5%, 10%, and 20%. Able to select parallel or series increasing accuracy of in-circuit testing. Auto-off in 5min, 15min(default), 30min, or 60min are selectable.
3 Measurement Speeds – Slow(2 times per second), medium(5 times per seconds) and fast(20 times per second).
Tolerance Comparison – Equipped with audible/visual alarm, and counter features for tolerance fail/pass test.
Data Logger – The average, maximum, minimum value can be recorded via data logging mode.
Zeroing – Open/short zeroing eliminates connection errors, deliver more accurate measurement each times.
USB to PC – Transfer data to the PC/Laptop through a USB port, and exports to image file(jpg.), Excel and PDF report is available.
Portable – High resolution LCD with 5 digit display, lightweight, portable, and battery operated.
Applied in the product development, incoming inspections, or production line testing.
Brand
UNI T
Based on 0 reviews
Be the first to review “UT622A Digital Inductance LCR Meter”
-
Multimeters
DM 6013 LC METER
Features Of Handheld Mini Capacitor Meter Capacimeter DM6013L:
- Automatic in zeroing and polar selection
- Wide measuring range, covering 9 measuring sections from 0.1pF to 20,000uF
- Max. display: 1999 counts(3 1/2digits)
- Data Hold
- LCD backlight
- Two ways to test capacitance,input jack and meter pen,convenient to operate.
SKU: 4000 -
Clamp Meters
UT 205A+
1. 1000A AC current measurement2. 1000V AC/DC voltage measurement3. 600A inrush current measurement (UT206A+)4. Temperature (UT206A+)5. NCV (UT206A+)6. ACV frequency 10Hz～10kHz7. Jaw opening: 45mm8. Resistance / capacitance / frequency measurement9. Auto range / backlight / low battery indication10. Continuity / diode / duty cycle11. MAX/MIN12. Data hold / flashlight / relative mode13. Auto power off14. CAT II 1000V/CAT III 600VSKU: n/a
Related products
-
LCR Meter
UT620 Series Digital Micro Ohm Meters
UT620 series are used to measure DC low resistance through 4-wire method. Some of its features are: Comparison function to determine if the device is in good condition, unknown wire length calculation (FT/M); two-way data transmission by USB interface; built-in rechargeable lithium battery. UT620 can be used in narrow space for on-site troubleshooting, such as metal coating resistance/motor and small transformer winding resistance measurement, earth system joints/welding points/power distribution cabinet bus and lead connection inspection and more.
SKU: UN62B0TUOM -
LCR Meter
MS8910 Smart SMD Tester (R/C)
The Tester is a handheld and battery operated very convenient small Tool that is specially used to measuring SMD (Surface Mounting Device), there are Chip type resistor, Chip type capacitor, and diode. Moreover, the Tester also has the continuity checking function.
● Display 3000 counts
● Auto Ranging
● Auto Power Off
● Data Hold
● Low Battery Display
● Auto Scanning
● Diode Check Open Voltage 2.8V
● Diode Testing Current 2mA
● Continuity Buzzer <30ΩSKU: n/a -
LCR Meter
UT601 Inductance Capacitance Meters
UT600 series RCL meter is a kind of 3.5-bithandheld digital meter with stable performance, safety, reliability, highaccuracy and manual range. It can be used to measure the magnification times β of audion, diode forward voltage drop and circuit continuity. UT601has wide capacitance measurement range from 0.1pF～20mF and highaccuracy. UT602 can hold data. UT 600 series is applicable to testingresistance, capacitance and inductance of electronic laboratory, productionline, maintenance point and teaching. It is the ideal tool of maintaining formany users
SKU: n/a -
LCR Meter
UNI-T UT622E Handheld LCR Meter
Features of UNI-T UT622E Handheld LCR Meter:
- Up to 0.1% measurement accuracy
- High-brightness white backlight
- Ultra-low power consumption and long battery life (8 hours)
- Maximum test speed: 20 times/s
- Constant 100Q output impedance
- Data hold and recording mode
- Standard Mini-USB interface, SCPI command set
SKU: n/a
There are no reviews yet.