-29%

Battery Load Tester – BT 100D

Availability:

7 in stock


  • 100 Amp Digital Battery Load Tester
  • Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
  • Bright, LED Digital Display–indicates both voltage and test results
  • Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
  • Super-Grip Battery Clamps–heavy-duty and color-coded
  • Baked Enamel, Steel Case–ventilated to keep cool
  • Rubber Insulated Carrying Handle–for comfort and safety
  • Checks both Battery and Charging System

5,000 7,000

7 in stock

Compare

The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.

Category: Tag:
Weight 0.7 kg
Dimensions 15 × 8 × 6 cm

12 Volt Battery Analysis

Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:

1.
 GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.

2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.

3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.

4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).

NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.

Brand

TITAN

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Battery Load Tester – BT 100D”

There are no reviews yet.

  • MS6812 Cable Tracker

    0 out of 5
    (0)

    The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker

    ● Sound and Light Instruction
    ● Cont and Tone LED Light

    Applications
    – Judge Continuity of the Cables or Wires
    – Track the Cables or Wires, and Diagnose the Break Point
    – Receive the Tone Signal on the Cables or Wires(Telephone Line)
    – Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
    – Send a Single Solid or a Dual Alternating Tone to the Target Cables or Wires

    SKU: n/a
  • ,

    JM-B02 Professional Orange & Black Tool Bag

    0 out of 5
    (0)

    High-end tool bag (big size) JM-B02

    Assembly and repairing of household appliances, elevator and other large mechanical, the equipment of broadband and the building construction.

    Material: 600D oxford

    Size:

    JM-B02 360*160*210

    SKU: n/a
  • UT330C USB Datalogger

    0 out of 5
    (0)

    1. 60000 sets data storage

    2. PC software
    3. Trend capture to BMP/CSV/TXT files
    4. High/low temperature alarm, customizable user settings
    SKU: n/a
  • ,

    JM-CT4-12 Electrician Wire Stripping Tool

    (1)

     

    Features:

    • Standard specs, form-ground, knife-type blades for accuracy, easy stripping without nicking insulation.
    • Built-in wire cutter and looping holes.
    • Convenient plier nose and sharp edge for pulling out the wire easily without damaging the wire cores.
    • Spring-loaded automatic opening
    • Sharp serrated edges in a plier style for wire pulls and loops.
    SKU: n/a
  • MS8910 Smart SMD Tester (R/C)

    0 out of 5
    (0)

    The Tester is a handheld and battery operated very convenient small Tool that is specially used to measuring SMD (Surface Mounting Device), there are Chip type resistor, Chip type capacitor, and diode. Moreover, the Tester also has the continuity checking function.
    ● Display 3000 counts
    ● Auto Ranging
    ● Auto Power Off
    ● Data Hold
    ● Low Battery Display
    ● Auto Scanning
    ● Diode Check Open Voltage 2.8V
    ● Diode Testing Current 2mA
    ● Continuity Buzzer <30Ω

    SKU: n/a