CMP-2000 Digital clamp-on multimeter
5 in stock
It provides:
- AC current measurement (TRUE RMS) up to 1500 A and DC up to 2000 A.
- Measurement of INRUSH current in start-up phase of electrical device.
- AC voltage measurement (TRUE RMS) up to 750 V and DC up to 1000 V.
- Resistance measurement and continuity test:
– continuity test with acoustic signalling (beeper) for resistance below 30 Ω. - Capacitance measurement.
- Temperature measurement (Fahrenheit or Celsius).
- Frequency measurement.
- Duty cycle measurement.
- Diode test.
₨61,859 ₨65,809
5 in stock
Compare-
Universal clamp meter, enabling the maintenance of current measurements up to 2000 A, with the diameter of the clamp as 57 mm, and bus bar to 70 * 18 mm
The instrument has an electronic overload protection of all functions and ranges.
| Weight | 0.6 kg |
|---|---|
| Dimensions | 28 × 11 × 5 cm |
AC current measurement (TRUE RMS) up to 1500 A and DC up to 2000 A.
Measurement of INRUSH current in start-up phase of electrical device.
AC voltage measurement (TRUE RMS) up to 750 V and DC up to 1000 V.
Resistance measurement and continuity test:
- continuity test with acoustic signalling (beeper) for resistance below 30 Ω.
Capacitance measurement
Temperature measurement (Fahrenheit or Celsius).
Frequency measurement.
Duty cycle measurement.
Diode test.
Additionally:
- safe, insulated measuring clamp,
- autoranging,
- „DATA HOLD” function, for holding measured values,
- backlit LCD,
- „DC ZERO” mode of measurement for DC current, possibility to zero the display and reading relative actual value less stored „zero” value,
- „MAX/MIN” function,
- over range indication,
- „AUTO-OFF” function after 30 min.
Electric security:
- measurement category: CAT IV 600 V acc. to EN 61010 – 1,
- protection class acc. to EN 60529: IP20,
Other technical data:
- power supply, 9 V battery type 6LR61,
- display: 6600 counts, backlit LCD,
- continuity test: threshold 30 Ω,
- diode test: test current of 0,8 mA , typical open circuit voltage 3,2 V DC, typical,
- low battery indication: BAT displayed,
- over range indication: ‘OL’ displayed,
- temperature sensor: type K thermocouple,
- input impedance: ca.10 MΩ (V DC and V AC),
- AC bandwidth: 50…500 Hz,
- auto power OFF: 30 minutes,
- dimensions: 281 x 108 x 53 mm,
- weight: 570 g (with battery),
- accordance with following standards: EN 61010 – 1, EN 61010 – 2-032.
Rated operational conditions:
- able to open the clamp: Ø 57 mm wire 70 x 18 mm bus bar,
- operating temperature: 0…+50 °C,
- storage temperature: -20…+60 °C,
- operating altitude: max 2000 m.
DC current measurement
| Range | Resolution | Accuracy |
| 0,0…659,9 A | 0,1 A | ±(2,0% m.v. + 5 digits) |
| 660…2000 A | 1 A | ±(3,0% m.v. + 5 digits) for 660…1000 A |
| ±(5,0% m.v. + 5 digits) for 1000…2000 A |
AC current measurement (TRUE RMS)
| Range | Resolution | Accuracy |
| 0,0…659,9 A | 0,1 A | ±(2,0% m.v. + 10 digits) for 50…60 Hz |
| ±(3,0% m.v. + 10 digits) for 61…400 Hz | ||
| 660…1500 A | 1 A | ±(2,5% m.v. + 10 digits) for 50…60 Hz i 660…1000 A |
| ±(3,5% m.v. + 10 digits) for 61…400 Hz and 660…1000 A |
||
| ±(5,0% m.v. + 10 digits) for 50…400 Hz and 1000…1500 |
DC voltage measurement
| Range | Resolution | Accuracy |
| 0,000…6,599 V | 0,001 V | ±(0,5% m.v. + 2 digits) |
| 6,60…65,99 V | 0,01 V | |
| 66,0…659,9 V | 0,1 V | |
| 660…1000 V | 1 V |
AC voltage measurement (true RMS)
| Range | Resolution | Accuracy |
| 0,000…6,599 V | 0,001 V | ±(1,5% m.v. + 8 digits) for 50…500 Hz |
| 6,60…65,99 V | 0,01 V | |
| 66,0…659,9 V | 0,1 V | |
| 660…750 V | 1 |
Resistance measurement
| Range | Resolution | Accuracy |
| 0,0…659,9 Ω | 0,1 Ω | ±(1,0% m.v. + 5 digits) |
| 0,660…6,599 kΩ | 0,001 kΩ | |
| 6,60…65,99 kΩ | 0,01 kΩ | |
| 66,0…659,9 kΩ | 0,1 kΩ | |
| 0,660…6,599 MΩ | 0,001 MΩ | ±(2,0% m.v. + 5 digits) |
| 6,60…66,00 MΩ | 0,01 MΩ | ±(3,5% m.v. + 5 digits) |
Capacitance measurement
| Range | Resolution | Accuracy |
| 0,0…6,599 nF | 0,001 nF | ±(3,0% m.v. + 30 digits) |
| 6,60…65,99 nF | 0,01 nF | ±(3,0% m.v. + 10 digits) |
| 66,0…559,9 nF | 0,1 nF | ±(3,0% m.v. + 30 digits) |
| 6,600…59,999 µF | 0,001 µF | ±(3,0% m.v. + 10 digits) |
| 66,00…659,99 µF | 0,01 µF | |
| 660…659,999 µF | 0,100 µF | |
| 0,660…6,600 mF | 0,001 mF |
Frequency measurement
| Range | Resolution | Accuracy |
| 10…65,99 Hz | 0,01 Hz | ±(0,1% m.v. + 5 digits) |
| 66,0…659,9 Hz | 0,1 Hz | |
| 0,660…6,599 kHz | 0,001 kHz | |
| 6,60…65,99 kHz | 0,01 kHz | |
| 66,0…659,9 kHz | 0,1 kHz | |
| 0,660…1,000 MHz | 0,001 MHz |
Temperature measurement
| Range | Resolution | Accuracy |
| -20…0°C | 1°C | ±(2,0% m.v. + 3°C) |
| 0…399°C | ±(1,0% m.v. + 2°C) | |
| 400…1000°C | ±(2,0% m.v. + 3°C) | |
| -4…31°F | 1°F | ±(2,0% m.v. + 6°F) |
| 32..749°F | ±(1,0% m.v. + 4°F) | |
| 750…1832°F | ±(2,0% m.v. + 6°F) |
Duty cycle measurement
| ange | Resolution | Accuracy |
| 5…95% | 0,1% | ±(2,0% m.v. + 10 digits) |
„m.v.”- measured value
Brand
SONEL
Based on 0 reviews
Be the first to review “CMP-2000 Digital clamp-on multimeter”
-
Wire & Cable Testers
UT681HDMI Cable Tester
1. Tests HDMI/MINI-HDMI cables
2. Fastline collocation type: A with A, A with C and C with C
3. Checks circuit breakage, short circuit, cross circuit and the missing wire
4. 20 visible LED indicators
5. Can toggle between scan and full display test modes
6. Single key operation
7. Manual/auto power off (after 10-minute inactivity)
8. Low battery indication
9. CE certification
10. Power supplied by 9V layer-built battery
SKU: n/a -
DC Power Supplies
TITAN TN 305DS DC Power Supply
Operating Conditions
Supply power: AC 220-240V, 50Hz/60Hz.
Working Temperature: -10°C ~ 40 °C
Relative Humidity: ‹ 90%
Storage Conditions: -10°C ~ 40 °C
Relative Humidity: ‹ 80%
Stable Voltage
The output voltage is between 0 and nominal value continuously adjustable
Voltage Stability: ≤0.01% +2mV
Load Stability: ≤ 0.01% +2mV
Recovery Time: ≤100µS
Temperature Coefficient: ≤ 200PPM/°C
Ripple Noise: ≤1 MVRMS(RMS)
Stable CurrentPower Stability: 0.1% + 3mA
Load Stability: 0.2% + 3mA
Ripple Noise : ≤2mArms(RMS)
The output current is between 0 and nominal value continuously adjustable
SKU: n/a -
Corbon Mono Oxide Meter
Uni-T UT337 Carbon Monoxide Meter
Suitable for use everywhere from in the house to restaurants, offices and industrial areas, the UT337A measures the exact value of carbon monoxide (CO) present in the air. Featuring a built-in sensor integrated into the top of the unit, the UT337A measures CO content from 0-1000ppm with accuracy of ±5% (5ppm) and resolution of 1ppm. The sensor is also designed to adjust rapidly to changes, ensuring you always get a stable, accurate reading. When CO levels exceed a certain threshold, the UT337A will alert the user by using a combination of audible and LED light indicators. The alarm is configurable to the user’s specification and it is also possible to use this meter to calculate temperature values.
SKU: n/a -
Oscilloscopes
UNI-T MSO3152E 150MHz Mixed Signal 2 Channel Digital Oscilloscope
Analog bandwidth 150MHz 250MHz Channels 2+16 digital 4+16 digital 2+16 digital 4+ 16digital Sampling rate (Analog) 2.5GS/s (Single channel), 1.25GS/s (Dual channels) Sampling rate (Digital) 1.25GS/s (Eight channels), 625MS/s(Sixteen channels) Memory depth 70Mpts Waveform capture rate 200,000wfms/s Time base scale 2ns/div~50s/div (Real-time sampling rate, memory depth display ) Time base scale (digital) 2ns/div~40S/div[Step by 1-2-4 stall] Input impedance (1MΩ±1%) II (20pF±3pF) Input impedance digital (101kΩ±1%) II (9pF±1pF) Vertical scale 1mV/div~20 V/div (1 MΩ) DC gain accuracy <5mV: ±3%, ≥5mV: ±2% Waveform record 100,000 frames Trigger types Edge, Runt, Window, Nth Edge, Delay, Overtime, Duration, Setup/Hold, Pulse Width, Slop, Video, Code; RS232/UART, I2C, SPI, USB,
CAN, LIN, FlexRayBus decode RS232/UART, I2C, SPI, USB, CAN, LIN, FlexRay Waveform operations A+B, A-B, A×B, A/B, FFT, editable advanced and logical operations Auto measurements
Max, Min, High, Low, Ampl, Pk-Pk, Middle, Mean, CycMean, RMS, CycRMS, Period, Freq, Rise, Fall, RiseDelay, FallDelay, +Width,
-Width, FRR, FRF, FFR, FFF, LRF, LRR, LFR, LFF, +Duty, -Duty, Area, CycArea, OverSht, PreSht, Phase, 34 parameters in totaldigital
channel: Freq, Period, +Width, -Width, +Duty, -Duty, RiseDelay A→B,FallDelay A→B, Phase A→B, Phase B→AMeasurement display 5 types Measurement statistics Average, Max, Min, standard deviation and number of measurements Frequency counter 6 bits Standard interfaces USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail), AWG,UT-M15 logic analyzer probe, VGA Standard Accessories
USB interface cable UT-D14 Passive Probe x 2/4 (1 x , 10 x switchable,300MHz,) UT-P06 Passive Probe x 2/4 (1 x , 10 x switchable,200MHz,) UT-P05 16CH Logic analyzer probe UT-15M SKU: n/a -
LCR Meter
UT620 Series Digital Micro Ohm Meters
UT620 series are used to measure DC low resistance through 4-wire method. Some of its features are: Comparison function to determine if the device is in good condition, unknown wire length calculation (FT/M); two-way data transmission by USB interface; built-in rechargeable lithium battery. UT620 can be used in narrow space for on-site troubleshooting, such as metal coating resistance/motor and small transformer winding resistance measurement, earth system joints/welding points/power distribution cabinet bus and lead connection inspection and more.
SKU: UN62B0TUOM
Related products
-
Clamp Meters
UT-CS09A Flex Clamp Sensor
Specifications Range UT-CS09A AC current (A) 30A/300A/3000A ±(3%+5) Frequency response (Hz) 45Hz~500Hz √ Features Flex clamp size UT-CS09A: 25.4cm (10 inches); UT-CS09C: 45.7cm (18 inches) Operating temperature 0℃~50℃ Storage temperature -20°C~60°C Storage humidity ≤80%RH Low battery indication About 3.3V Range selection Manual General Characterisitics Power 1.5V battery (R03) x 3 Product color Red and grey Product net weight 260g Product size 267mm x 119.4mm x 34mm Standard accessories Batteries, BNC adapter Standard individual packing Blister, English manual Standard quantity per carton 10pcs Standard carton measurement 495mm x 405mm x 225mm Standard carton gross weight 7kg SKU: n/a -
Clamp Meters
UT216A 600A Digital Clamp Meters
UT216 series true RMS digital clamp meter is a new-generation practical electrotechnical measurement meter which has the features of high reliability, high safety, automatic range and handheld type, has full-range overload protection and unique appearance design, is more excellent in performance, and is an ideal tool for detection, maintenance and repair of various universities and colleges, smelting, communication, manufacturing, petroleum, national defense, electrical, power and circuit equipment.
UTD216A (main features)- 1、600A AC current measurement
- 2、True RMS response for ACV and ACA
- 3、99.99mF capacitance measurement
- 4、Non-contact voltage detection with LED indication
- 5、Flashlight for working at dark environment
SKU: n/a -
Clamp Meters
MT87 3 1/2 Digits LCD Digital Clamp Meter
This meter features a portable design, 31/2 LCD display and 25mm jaw opening, which can provides various measurements for AC/DC voltage, AC current, resistance, diode and continuity buzzer. It is also with functions of date hold, low battery indication, overload indication, etc. More detailed product information, please refer to the English manual.
SKU: MT 87 CLAMP METER
There are no reviews yet.