-5%

LKZ-720 Wires and pipe locator

Availability:

2 in stock


Features:

  • the function 3D in the receiver – detecting the direction of current flow and accurate locating the object,
  • phase detection mode,
  • receiver operation with four transmitters at the same time to locate interruptions or distinguish wires,
  • a LED bright torch,
  • headphone socket in receiver,
  • screens backlight for work in dark,
  • transmission battery status and settings of the transmitter to the receiver
  • operation in wide range of rated voltage, up to 500V RMS,
  •  measurement of voltage at the object to 500 Vrms,
  • three levels of transmitter amplification,
  • automatic or manual selection of transmitter operation modes,
  • five modes of wire tracer operation – voltage, current, current-voltage, power and clamp,
  • software upgrade via USB,
  • additional accessories enable precise localization – such as contact or non-contact probes and measurement clamp.

200,000 210,000

2 in stock

Compare
  • Detection of wires and cables (live or not)
    • detection of cables in ceilings, walls and floors,
    • detection of breaks in cables,
    • tracing cables in building installation,
    • locating power points and switches in buildings,
    • locating short circuits between leads,
    • tracing shielded cables,
    • tracing cables in metal ducts.
  • Identification of fuses on the distribution board.
  • Tracing underground cables.
  • Tracing conductive water and heating pipelines.
  • Non-contact detection of live cables.

Electric security:

  • type of insulation: double, according to EN 61010-1
  • measurement category: CAT III 600V acc. to EN 61010-1
  • transmitter’s protection class acc. to EN 60529: IP67
  • receiver’s protection class acc. to EN 60529: IP40

Other technical data:

  • transmitter’s power supply: four AA alkaline battery or NiMH rechargeable battery
  • transmitter’s max working voltage: 500 Vrms (707 Vampl)
  • detector’s max range („I” mode) 2m
  • non-contact neon max range: 20 cm (in air), 3 cm (in concrete)
  • receiver’s power supply: battery 9V 6LR61 alkaline

Rated operational conditions:

  • operating temperature -10°C…+50°C

Brand

SONEL

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “LKZ-720 Wires and pipe locator”

There are no reviews yet.

  • Insulation Resistance Testers UT512

    0 out of 5
    (0)

    UT510 series is a kind of intelligent insulation tester. The device circuit design takes microcomputer technology design as the core and combines the large scale integrated circuit with digit circuit. It is equipped with strong measuring software and data processing software. It is applied to the parameter measurement of insulation resistance, voltage and low resistance. It has stable performance and simple operation. It is applicable to on-site measurement and repair of the electrical equipment and charging line. It is the ideal tool of maintaining electrical equipment. It is also used for smelting, communication, manufacture, fossil oil, national defense, electricity, chemical industry and circuit.

    SKU: n/a
  • Et-8908 Intelligent Multimeter Precise Auto-sensing Capacitance Voltage

    0 out of 5
    (0)

    Et-8908 Intelligent Multimeter Precise Auto-sensing Capacitance Voltage

    SKU: n/a
  • UTD2102CEX-II Digital Storage Oscilloscope

    0 out of 5
    (0)

    1. 2 channels

    2. 70MHz/100MHz bandwidth; 1GSa/s real-time sampling rate
    3. Up to 28Mpts memory depth
    4. Calibration signal output: 10Hz, 100Hz, 1kHz (by default),
    10kHz or 100kHz
    5. Max 10Mpts waveform record
    6. 8-inch TFT LCD, WVGA (800X480)
    SKU: n/a
  • TDR-410 Cable Fault Locator

    0 out of 5
    (0)
    • Features:

      • automatic or manual mode:
        • the automatic fault location (AFL),
        • mode with manual range selection and sensitivity,
        • single measurement triggered manually or scanning continuous,
      • 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
      • maximum length of cable up to 4000 m one end of the cable,
      • “Dead zone” measure limited to 0.5 m,
      • 2.5 “LCD screen with backlight,
      • scan automatically or manually trigger,
      • sensitivity set manually or automatically adjusted,
      • adjustable impedance matching,
      • propagation coefficient adjustment 1% to 99%,
      • waterproof and resistant to mechanical housing.
      • small size and weight.
      • economical power system – 30 hours of continuously scan on one battery set..

      Accessories:

      • 0,6 m double-wire lead: WAPRZ0X6DZBB
      • red crocodile clip: WAKRORE20K02
      • Krokodylek czarny: WAKROBL20K01
      • cover M-2: WAFUTM2
    SKU: n/a
  • CLAMP METER AC BM 528F

    0 out of 5
    (0)
    Product Description
    BM528F AC Digital Clamp meter Technical parameters
    Functions
    Range
    Accuracy

    (BM528F)
    DC Voltage
    200mV/2V/20V/200V/1000V
    ±(0.8%+2)
    AC Voltage
    2V/20V/200V/700V
    ±(1.2%+5)
    AC Current
    2A/20A/200A/600A
    ±(2%+10)
    Ω Resistance
    200/2K/20K/200K/2M/20MΩ
    ±(1%+3)
    Capacitance
    20n/200n/2μ/20μ/200μ/2mF
    ±(3%+5)
    Frequency
    200/2K/20K/200K/2M/20MHz
    ±(0.5%+3)
    ℃ / ℉
    -50℃ ~1000℃

    -58℉~1832℉

    ±(1%+5)

    ±(1.2%+6)
    SKU: n/a