- Location damaged power cables.
- Fault location copper telecom cables.
- Coaxial cable fault location.
- Fault location wiring infrastructure.
- Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
- Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
TDR-410 Cable Fault Locator
Out of stock
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
₨0
Out of stock
CompareDechnical data:
- Ranges Meters: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
- Ranges Feet: 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 14000.
- Range Selection: Manual range control / Auto range.
- Accuracy: 1% of selected range*.
- Resolution: Approx 1% of range.
- Minimum cable lenght: 4m (14ft).
- Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP.
- Velocity Factor: Adjustable from 1% to 99%.
- Output Pulse: 5 volts peak to peak into open circuit.
- Output Impedance: Selectable 25, 50, 75 & 100 Ω.
- Output Pulse: Width 3 ns to 3 µs, Automatic with range.
- Scan Rate: 2 scans/second or scan held, pre set for each range scale.
- Tone Generator: 810 – 1100Hz.
- Battery Life: 30 hours continuous scanning.
- Power Supply: 6 volts 4 x 1.5 AA Alkaline cells, on-screen low voltage indicator.
- Power Down Selectable: 1, 2, 3, 5 minutes or disabled.
- Back Lit Display: 128 x 64 pixel.
- Voltage Protection: 250 volts AC.
- Operating Temp: -10º / 50ºC.
- Storage Temp: -20º +70° C.
- Dimensions: 165 x 90 x 37 mm (6.5 x 3.5 x 1.5 ins).
- Weight: 350 g (12oz).
- Safety: IEC 61010-1, EN 60950.
- EMC: BS/EN 61326-1.
- Water/Dust Proof: IP54
Based on 0 reviews
Be the first to review “TDR-410 Cable Fault Locator”
-
Battery Testers
UNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Battery TestersUNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Model UT3513 Resistance range 20m Q/200m Q/2Q/20Q /200 Q/2kQ/20kQ Resolution 1 u Q/10 u Q/100 u Q/lmO/lOmQ/lOOmQ/1 Q/10Q/100Q Test current 1A/1A/100mA/10mA/1mA/1mA/100 uA/10 u A/l uA Testing terminal opencircuit voltage <1V/<1V/<1V/<1V/<5V/<5V/<5V/<5V/<3V/ Measured parameter DC resistance Basic accuracy Slow: 0. 1%; Medium: 0. 2% Maximum reading 22000 Range mode Auto/Manual/nominal Calibration Short-circuit full range zeroing Sorting function 3types of resistance and voltage input: exceeds upper limit/exceeds lower limit/within the range,2 types of sorting result output: PASS/FAIL Comparing method Absolute tolerance, percentage tolerance, direct-reading comparison Trigger mode Internal, external Test terminal Four-terminal measurement Button functions Lock 一一 keyboard lock, OK 一一 screenshot System setup Language: Chinese/English, key tone setting Interfaces & protocols Handler interface, RS232, USB DEVICE and USB HOST communication interface,SCPI and Modbus protocol Upper computer software V Power AC 100~240V 50/60Hz Display 4.3-inches LCD SKU: n/a -
Oscilloscopes
UPO2102CS Ultra Phosphor Oscilloscope
Features and Benefits:
1、Sample Rate up to 1GS/s;
2、Channels 2/;
3、Bandwidth 100MHz,;
4、Memory Depth 32Mpts(Standard);
5、Waveform Capture Rate up to 30,000wfms/s;
6、With 256 level intensity grading display;
7、Up to 65,000 frames for Waveform Record ,Replay;
8、Support serial bus trigger and decoding;
9、8 inches, TFT LCD,WVGA(800*480);
10、Interface:USB Host, USB Device, LAN, VGA, AUX OUT, 10MHz input/output.SKU: UT21P02CSO -
Multimeters
UT195DS Professional Digital Multimeters
1. IP65 rating, 2m drop proof, CAT III 1000V, CAT IV 600V
2. Large 6000-count LCD screen
3. 5/s sampling rate
4. True RMS
5. ACV 750V 5kHz bandwidth
6. (AC+DC) or (AV+FREQ) , dual mode
7. Flashlight
8. Auto LCD backlight controlled by light sensor (can be turned off)
9. LoZ voltage test, for ghost voltage measurement
10. Motor phase sequence measurement with 2 probes
11. 20A current measurement (max 30 seconds)
12. 31 analogue bar
13. Low pass filter, 1kHz 3dB attenuation
SKU: n/a -
There are no reviews yet.