TDR-410 Cable Fault Locator
Out of stock
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
₨0
Out of stock
Compare- Location damaged power cables.
- Fault location copper telecom cables.
- Coaxial cable fault location.
- Fault location wiring infrastructure.
- Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
- Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
Dechnical data:
- Ranges Meters: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
- Ranges Feet: 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 14000.
- Range Selection: Manual range control / Auto range.
- Accuracy: 1% of selected range*.
- Resolution: Approx 1% of range.
- Minimum cable lenght: 4m (14ft).
- Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP.
- Velocity Factor: Adjustable from 1% to 99%.
- Output Pulse: 5 volts peak to peak into open circuit.
- Output Impedance: Selectable 25, 50, 75 & 100 Ω.
- Output Pulse: Width 3 ns to 3 µs, Automatic with range.
- Scan Rate: 2 scans/second or scan held, pre set for each range scale.
- Tone Generator: 810 – 1100Hz.
- Battery Life: 30 hours continuous scanning.
- Power Supply: 6 volts 4 x 1.5 AA Alkaline cells, on-screen low voltage indicator.
- Power Down Selectable: 1, 2, 3, 5 minutes or disabled.
- Back Lit Display: 128 x 64 pixel.
- Voltage Protection: 250 volts AC.
- Operating Temp: -10º / 50ºC.
- Storage Temp: -20º +70° C.
- Dimensions: 165 x 90 x 37 mm (6.5 x 3.5 x 1.5 ins).
- Weight: 350 g (12oz).
- Safety: IEC 61010-1, EN 60950.
- EMC: BS/EN 61326-1.
- Water/Dust Proof: IP54
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-410 Cable Fault Locator”
-
Usb Tester
UT658 A USB Testers
Features of UT658 Series USB Testers
Certifications: CE, UKCA
● Type-A/C interface
● CE certification
● 10 sets of data storage
● Loop equivalent resistance measurement (1-480Ω)
● Same screen shows voltage, current, power, capacity, etc.
● Support fast charge protocol
SKU: n/a -
Function Generators
UTG2062B Function/Arbitrary Waveform Generator
1. 1μHz full-band resolution
2. 5MHz~30MHz pulse waveform, adjustable rise/fall time3. 14-bit/16-bit vertical resolution4. Two equivalent-performance channels5. Max arbitrary waveform length of 8k/16M points; 48/1616. non-volatile waveforms storageSKU: n/a
Related products
-
Wire & Cable Testers
UTP 04 100MHZ PROBE
Features Of UNI-T Best Passive Probe 100MHz UTP04:
This passive probe is good oscilloscope accessories, it is suitable for oscilloscope.
Stable performance and not easy to break.
This can provide a professional and accurate measurement.
Widely used, it can satisfy most peoples.
A good helper for instrument engineer.
SKU: n/a -
Wire & Cable Testers
LKZ-720 Wires and pipe locator
Features:
- the function 3D in the receiver – detecting the direction of current flow and accurate locating the object,
- phase detection mode,
- receiver operation with four transmitters at the same time to locate interruptions or distinguish wires,
- a LED bright torch,
- headphone socket in receiver,
- screens backlight for work in dark,
- transmission battery status and settings of the transmitter to the receiver
- operation in wide range of rated voltage, up to 500V RMS,
- measurement of voltage at the object to 500 Vrms,
- three levels of transmitter amplification,
- automatic or manual selection of transmitter operation modes,
- five modes of wire tracer operation – voltage, current, current-voltage, power and clamp,
- software upgrade via USB,
- additional accessories enable precise localization – such as contact or non-contact probes and measurement clamp.
SKU: n/a -
Wire & Cable Testers
UT681L Cable Tester
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
SKU: n/a
There are no reviews yet.