TDR-420 Time Domain Reflectometer/ Cable Fault Locator

Availability:

Out of stock


Product features

  • Possibility damage-free location of impedance changes of tested cables and wires such as:
    • shorted conductor,
    • open conductor / end of cable – useful during the inventory of warehouses and stores,
    • splice,
    • splitter,
    • water ingress,
    • wet splice,
    • bridge tap
    • or other changes.
  • Single measurement mode ONCE,
  • Continuously measurement mode CONT,
  • Tone signal generator TONE,
  • Two cursors to mark two places of damage along with an indication of the distance between them,
  • Built-in HELP function for easier interpretation of the reflectogram,
  • 11 available measuring ranges from 7 m to 6000 m,
  • „dead zone” limited to 0.6 m,
  • Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
  • manually set of sensitivity in 8 steps GAIN,
  • output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
  • Velocity of Propagation set in range from 10% to 99%,
  • tight and durable housing with IP67 ingress protection degree.
  • Small size and weight.

0

Out of stock

Compare

TDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.

Two cursors allow to determine the place of two damages simultaneously and the distance between them.

Thanks to the color 3,5” TFT display with a resolution of 320 x 240 pixels, the indication of the location of the damage is precise and the results easier to interpret.

Difficult environment conditions during measurement work are frequent problems encountered by electric installers and maintenance services. Thanks to the unique housing TDR-420 ensure a degree of protection on IP67 level, what means dustproof and protection against water penetration during short-term immersion. Therefore, working in very dusty terrain or accidental contact of the device with water will not affect the correct operation of the reflectometer.

 

Technical specification

  • Measurement ranges: 7, 15, 30, 60, 120, 250, 500 m, 1, 2, 3, 6 km / 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 20000 ft
  • Accuracy:1% of selected range
  • Resolution: Approx. 1% of selected range
  • Min. Cable length: 4 m / (14 ft)
  • Velocity of propagation VoP: Adjustable from 10 to…99% or 15…148,5 m/µs
  • Output Pulse: 5 Vp-p (open circuit)
  • Output Impedance: 25, 50, 75, 100, 120, 200 Ω
  • Output Impedance: 3 ns…3 µs (depends of range)
  • Scan rate / mode: Up to 3 scans / second (CONT) or single (ONCE)
  • Tone generator: 810 … 1110 Hz
  • Battery Life: Up to 8 hours of continuous scan
  • Power supply: 4 x alkaline batteries 1.5 V type AA or 4 x rechargeable batteries NiMH AA
  • Auto-OFF: 1, 3, 5, 10, 15 minutes or deactivated
  • Display: Color 3,5” LCD TFT, 320 x 240 pixels
  • Voltage protection: 400 V DC / 250 V AC
  • Dimensions: 220 x 98 x 58 mm (8.7 x 3.9 x 2.3 inches)
  • Weight: 487 g
  • Electromagnetic standard compatibility EMC: EN 61326-1
  • Water/ Dust Proof: IP67

Nominal condition of use

  • Operating temperature: -20..+70°C
  • Storage temperature: -30…+80°C at humidity <80%

Brand

SONEL

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “TDR-420 Time Domain Reflectometer/ Cable Fault Locator”

There are no reviews yet.

  • UT372D 2-in-1 Tachometer

    0 out of 5
    (0)

    UT372D 2-in-1 Tachometer is a reliable and safe tachometer, which combines contact and non-contact measurement modes. It is mainly used to measure Revolutions Per Minute(RPM) , frequency, surface velocity and length in the fields of motors, fans, automobiles, papermaking, etc.

    SKU: n/a
  • MS6812 Cable Tracker

    0 out of 5
    (0)

    The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker

    ● Sound and Light Instruction
    ● Cont and Tone LED Light

    Applications
    – Judge Continuity of the Cables or Wires
    – Track the Cables or Wires, and Diagnose the Break Point
    – Receive the Tone Signal on the Cables or Wires(Telephone Line)
    – Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
    – Send a Single Solid or a Dual Alternating Tone to the Target Cables or Wires

    SKU: n/a
  • UNI-T MSO3254E 250MHz Mixed Signal 4 Channel Digital Oscilloscope

    0 out of 5
    (0)
    Analog bandwidth 150MHz 250MHz
    Channels 2+16 digital 4+16 digital 2+16 digital 4+ 16digital
    Sampling rate (Analog) 2.5GS/s (Single channel), 1.25GS/s (Dual channels)
    Sampling rate (Digital) 1.25GS/s (Eight channels), 625MS/s(Sixteen channels)
    Memory depth 70Mpts
    Waveform capture rate 200,000wfms/s
    Time base scale 2ns/div~50s/div (Real-time sampling rate, memory depth display )
    Time base scale (digital) 2ns/div~40S/div[Step by 1-2-4 stall]
    Input impedance (1MΩ±1%) II (20pF±3pF)
    Input impedance digital (101kΩ±1%) II (9pF±1pF)
    Vertical scale 1mV/div~20 V/div (1 MΩ)
    DC gain accuracy <5mV: ±3%, ≥5mV: ±2%
    Waveform record 100,000 frames
    Trigger types Edge, Runt, Window, Nth Edge, Delay, Overtime, Duration, Setup/Hold, Pulse Width, Slop, Video, Code; RS232/UART, I2C, SPI, USB,
    CAN, LIN, FlexRay
    Bus decode RS232/UART, I2C, SPI, USB, CAN, LIN, FlexRay
    Waveform operations A+B, A-B, A×B, A/B, FFT, editable advanced and logical operations
     

     

    Auto measurements

    Max, Min, High, Low, Ampl, Pk-Pk, Middle, Mean, CycMean, RMS, CycRMS, Period, Freq, Rise, Fall, RiseDelay, FallDelay, +Width,
    -Width, FRR, FRF, FFR, FFF, LRF, LRR, LFR, LFF, +Duty, -Duty, Area, CycArea, OverSht, PreSht, Phase, 34 parameters in totaldigital
    channel: Freq, Period, +Width, -Width, +Duty, -Duty, RiseDelay A→B,FallDelay A→B, Phase A→B, Phase B→A
    Measurement display 5 types
    Measurement statistics Average, Max, Min, standard deviation and number of measurements
    Frequency counter 6 bits
    Standard interfaces USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail), AWG,UT-M15 logic analyzer probe, VGA
     

     

    Standard Accessories

    USB interface cable UT-D14
    Passive Probe x 2/4 (1 x , 10 x switchable,300MHz,) UT-P06
    Passive Probe x 2/4 (1 x , 10 x switchable,200MHz,) UT-P05
    16CH Logic analyzer probe UT-15M

     

    SKU: n/a
  • UT309D Professional IR Thermometer

    0 out of 5
    (0)

    1. EBTN screen, 20 sets of data storage (UT309D)

    SKU: n/a
  • UT343E Coating Thickness Gauge

    0 out of 5
    (0)

    Features of UT343E Coating Thickness Gauge

    Certificates: CE, UKCA

    ● Bluetooth APP
    ● Conductive coating measurement (like chromium, zinc, tin)
    ● Voice broadcast
    ● Durable probe

    ● Automobile mode
    ● Multiple measurement modes
    ● PC software analysis

    SKU: n/a