TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Out of stock
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
₨0
Out of stock
CompareTDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
Two cursors allow to determine the place of two damages simultaneously and the distance between them.
Thanks to the color 3,5” TFT display with a resolution of 320 x 240 pixels, the indication of the location of the damage is precise and the results easier to interpret.
Difficult environment conditions during measurement work are frequent problems encountered by electric installers and maintenance services. Thanks to the unique housing TDR-420 ensure a degree of protection on IP67 level, what means dustproof and protection against water penetration during short-term immersion. Therefore, working in very dusty terrain or accidental contact of the device with water will not affect the correct operation of the reflectometer.
Technical specification
- Measurement ranges: 7, 15, 30, 60, 120, 250, 500 m, 1, 2, 3, 6 km / 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 20000 ft
- Accuracy:1% of selected range
- Resolution: Approx. 1% of selected range
- Min. Cable length: 4 m / (14 ft)
- Velocity of propagation VoP: Adjustable from 10 to…99% or 15…148,5 m/µs
- Output Pulse: 5 Vp-p (open circuit)
- Output Impedance: 25, 50, 75, 100, 120, 200 Ω
- Output Impedance: 3 ns…3 µs (depends of range)
- Scan rate / mode: Up to 3 scans / second (CONT) or single (ONCE)
- Tone generator: 810 … 1110 Hz
- Battery Life: Up to 8 hours of continuous scan
- Power supply: 4 x alkaline batteries 1.5 V type AA or 4 x rechargeable batteries NiMH AA
- Auto-OFF: 1, 3, 5, 10, 15 minutes or deactivated
- Display: Color 3,5” LCD TFT, 320 x 240 pixels
- Voltage protection: 400 V DC / 250 V AC
- Dimensions: 220 x 98 x 58 mm (8.7 x 3.9 x 2.3 inches)
- Weight: 487 g
- Electromagnetic standard compatibility EMC: EN 61326-1
- Water/ Dust Proof: IP67
Nominal condition of use
- Operating temperature: -20..+70°C
- Storage temperature: -30…+80°C at humidity <80%
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-420 Time Domain Reflectometer/ Cable Fault Locator”
-
Tools and Hardware
JM OP06 OPENING TOOL
DescriptionItem Description:- Features:
– Stainless steel material make it more durable.
– Anti-corrosion with stainless steel forged process.
– Easier to disassemble the electronic part accessories.
– Common used in laptops, mobiles and tablets disassembling.
– Special rolling-wheel design for better use in opening.
– The end of the tool with anti-slip design make it easier for disassembling.
– Precision processing technology on the metal part for better protection on the product itself. - Brand: JAKEMY
- Model: JM-OP06
- Material: Stainless steel
- Color: Orange & silver
- Package Weight: 45.0 G / 1.59 Ounces
- Package Dimensions (L*W*H): 180*80*13 MM / 7.09*3.15*0.51 Inches200
SKU: n/a - Features:
-
Battery Testers
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
SKU: n/a -
-
IR Thermo Meters
UT301C Infrared Thermometers
UT301 series is a professional infrared thermometer that can determine the temperature by testing the infrared energy on the surface. It is used for fast and safe fault detections and maintenance of electric instrument and equipment, engines, motors, and HVAC refrigeration system.
SKU: UN30C1550CIR -
Clamp Meters
UT281C True RMS AC 3000A Flexible Clamp Meters
1. 2m drop proof, IP54, ETL/Intertek certified 3rdedition CE
2. Coil diameter: 0.75cm, bending length: 24.5cm for UT281A and 45.7cm for UT281C
3. Large LCD display for clear reading
4. True RMS
5. Long press INRUSH key for 2s to measure inrush current
6. Datahold, backlight, auto power off
SKU: n/a -
Digital Multi Meter
UNI-T UTL8212 High-Precision Compact DC Electronic Load Tester Single/Dual Channel 150V Power Supply Current Test – UTL821
Digital Multi MeterUNI-T UTL8212 High-Precision Compact DC Electronic Load Tester Single/Dual Channel 150V Power Supply Current Test – UTL821
Power supply test, adapter/charger test, battery test, lithium battery protection board test, ATE, component test, etc., commonly used in home appliance manufacturers, LCD and other computer component manufacturers, switching power supply and LED manufacturers, adapter charger manufacturers and other companies Production and testing use
SKU: n/a
Related products
-
Wire & Cable Testers
TDR-410 Cable Fault Locator
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
SKU: n/a -
-
Wire & Cable Testers
UT682 – Wire Tracker
UT682 – Wire Tracker consists of a transmitter and a receiver. It has functions like telephone wire tracking, network wire tracking, cable wire tracking, network wire check, etc. and it produces fast and accurate measurements. UT682 is an ideal tool for personnel to install and maintain network systems with communication lines and integrated wiring circuits.
SKU: n/a -
Wire & Cable Testers
LKZ-1000 Wires and pipe locator
- Passive or active modes of tracing.
- Detection of underground live wires.
- Detection of underground wires with no voltage (radio mode).
- Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).
- Tracing metallic or non-conductive pipes using an additional probe.
- Tracing non-conductive pipelines using a “floating” probe.
- Tracing a determined cable.
- Determining the depth of a cable.
SKU: n/a
There are no reviews yet.