● 9999-count LCD display with analogue bar
● 250V~1000V DC insula�on resistance test
● 200mA earth-resistance con�nuity test
● Loop impedance/Prospec�ve Fault Current (PFC)
/Prospec�ve Short Current (PSC) test
● Lock test
● RCD trip �me test and the data storage with one key
● Full/Half wave and count downing (30s) test mode
selectable
● 0°/180° phase angle op�on to detect the fastest
trigger �me
● Trip current test of RCD trip �me X2
● RCD trip trigger current test
● Phase sequence and missing test
● AC/DC voltage auto check and test
● Connec�on check with status real-�me display
● White backlight; auto power of
Brand
UNI T
Based on 0 reviews
Be the first to review “UT595 Multifunction Installation Testers”
-
DC Power Supplies
TITAN TN 305DS DC Power Supply
Operating Conditions
Supply power: AC 220-240V, 50Hz/60Hz.
Working Temperature: -10°C ~ 40 °C
Relative Humidity: ‹ 90%
Storage Conditions: -10°C ~ 40 °C
Relative Humidity: ‹ 80%
Stable Voltage
The output voltage is between 0 and nominal value continuously adjustable
Voltage Stability: ≤0.01% +2mV
Load Stability: ≤ 0.01% +2mV
Recovery Time: ≤100µS
Temperature Coefficient: ≤ 200PPM/°C
Ripple Noise: ≤1 MVRMS(RMS)
Stable CurrentPower Stability: 0.1% + 3mA
Load Stability: 0.2% + 3mA
Ripple Noise : ≤2mArms(RMS)
The output current is between 0 and nominal value continuously adjustable
SKU: n/a -
Insulation Tester
JM Z16 HEAT INSULATION MAT
JAKEMY JM-Z16 Magnetic Heat Insulation Silicone anti-static Working Mat for Soldering Assembling Electronics DIY Repair.
Feature:
Brand new and high quality.
Heat-resistant coefficient: 300 Celcius degree (hot wind) / 230 Celcius degree (direct contact).
Anti-static coefficient: 1*10E12ohm.
Units design, easy to keep track of parts.
Food grade material, non-toxic and safe in use. 6. Suitable for electronics devices repairing.Accessories:
Anti-static and heat-proof working mat*1SKU: n/a -
Clamp Meters
UT202BT Smart AC Clamp Meter
1. Button-design clamp meter
2. One-hand operation and easy to use
3. True RMS / 9999 counts
4. Jaw opening: 28mm
5. Bluetooth 5.0
6. 600V DC voltage measurement
7. 600V AC voltage measurement
8. 600A AC current measurement
9. Inrush current measurement
10. Dual display: V+HZ and A+HZ
11. Temperature measurement
12. Low pass filter measurement
13. Bright backlight / Flashlight
14. Non-contact voltage (NCV)
15. CAT III 600VSKU: n/a -
Clamp Meters
UT 205A+
1. 1000A AC current measurement2. 1000V AC/DC voltage measurement3. 600A inrush current measurement (UT206A+)4. Temperature (UT206A+)5. NCV (UT206A+)6. ACV frequency 10Hz～10kHz7. Jaw opening: 45mm8. Resistance / capacitance / frequency measurement9. Auto range / backlight / low battery indication10. Continuity / diode / duty cycle11. MAX/MIN12. Data hold / flashlight / relative mode13. Auto power off14. CAT II 1000V/CAT III 600VSKU: n/a
There are no reviews yet.