The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Clamp Meters
UT213C ACA DCA Digital Clamp Meters
Main Features
1. 10A/400A AC/DC measurement with Hall-effect sensor
2. Auto range makes measurement faster and more effective
3. 4000 display count, 3/s sampling rate
4. True RMS measurement
5. NCV, Non-Contact AC Voltage testing
6. Frequency and duty ratio measurement
7. MAX/MIN mode
8. Relative mode
9. Flashlight function for measuring at night or in the dark
10. K-type point contact temperature probe for temperature measurement
11. Large jaw of 30mm
12. Data hold
13. LCD backlight
14. Auto power off
15. 1m drop proof
16. Complies with CE (European Union) directives
SKU: n/a -
Multimeters
UT58A General Digital Multimeters
Product Features
1. 2,000 display count, 2~3/s sampling rate
2. Large 60mm×54mm LCD screen
3. Function symbols and test lead connecting indication for all ranges
4. Capacitance and transistor measurement
5. Diode and buzzer continuity
6. Data hold
7. Auto power off
8. 20A AC/DC current measurement
9. Complies with CE (European Union) directives
SKU: n/a -
Function Generators
UNI-T UTG4162A Function/Arbitrary Waveform Generator
bandwidth 160MHz Channels 2 Sampling rate 500MS/s Waveforms Sine, square, ramp, harmonic, pulse, noise, DC voltage, arbitrary Working modes Output on/off, continuous, modulation, sweep, burst Modulations AM, FM, PM, ASK, FSK, PSK, BPSK, QPSK, OSK, PWM, SUM, QAM Frequency Characteristics Sine 1μHz~160MHz Square/Pulse 1μHz~50MHz Slope 1μHz~4MHz Harmonic 1μHz~80MHz Noise (-3dB) 160MHz bandwidth Resolution 1μHz Arbitrary Waveform Frequency range 1μHz~40MHz Length 8~32Mpts Vertical resolution 16 bits Min rise/fall time (typical: 1Vpp) <5ns General Characteristics Power 100V~240V ACrms, 50Hz/60Hz Display 8-inch TFT LCD, WVGA (800 x 480) Product color White and grey Product net weight 3.5kg Product size 336mm x 164mm x 108mm Standard accessories BNC-BNC cable x 2, USB interface cable, PC software CD, power cord Standard individual packing Carton box Standard quantity per carton 1pcs Standard carton measurement 405mm x 225mm x 265mmv SKU: n/a
There are no reviews yet.