Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
-
Digital Multi Meter
18B WINHY DMM
Description
Features:
Multifunction:Can accurately measure AC/DC voltage, AC/DC current,resistance,capacitance,frequency,diode,LED test and continuity testing.
Portable Design:There is a back bracket for supporting multimeter,and also can collect test probe for your convenience.
Widely use:It’s perfect tool for the laboratory,factory and electricity.
Easy to Use & Clear to Read:With large LCD Backlight display,convenient to use and read.
More advantages:Auto power off,range,select,True RMS,data hold,over range indication and low voltage display.SKU: n/a -
Oscilloscopes
UTD2025CL Digital Storage Oscilloscope
1. Dual analog channels width range 1mV/div~20V/div;
2. 7 inches widescreen LCD displays;
3. Special Print Scree Feature;
4. Supports plug-and-play USB storage device. Communication with and remote control of computer through the USB device;
5. USB drive system software upgrade;
6. Storage of waveforms setups and interfaces waveforms and setups reproduction;
7. Automatic measurement of 28 waveform parameters;
8. Unique waveform recording and replay function;
9. Multilingual menu displays.
SKU: n/a -
Multimeters
UT61B Modern Digital Multimeters
UT61 Series Digital Multimeters are products designed for multi-functional, high precision, high performance and automatic measurements.
- 1、Large LCD screen；
- 2、High resolution analog pointer display；
- 3、Full range overload protection；
- 4、Data hold, REL, Peak value measurement；
- 5、Low battery indication, backlight, and sleep mode；
- 6、External interface supports RS-232C and USB cable.UT61Series can measure AC/DC voltage and current, resistance, diode, circuit continuity, capacitance, frequency, temperature, hFE, electromagnetic induction, etc.
UT61 Series complies with the standard IEC61010: CAT. III 1000V, CAT.IV 600V; they are widely used in Industrial Production and Service, Technological Research and Design, College Education (Laboratory, Courses), and Automotive Industry.
SKU: n/a
Related products
-
Battery Testers
UT673A Battery Testers
Features of UT673A Battery Testers
Certifications: CE, UKCA, FCC
● 12V cranking lead acid battery test
● 12/24V charging or cranking system test● Display battery capacity, voltage, resistance and life● Four-termina Kelvin test● 10 types of battery standards● Language option (Chinese/English)● Test without battery disassembly● LED color indication for test result (UT673A)● Print on-line and real-time test reports (UT675A)● USB data transfer (UT675A)SKU: n/a -
Digital Multi Meter
UNI-T UTi320V Thermal Image
Technical Specifications of UTi320V Thermal Image:
Specifications Model UTi320V Temperature range -20~350℃ -4℉~662℉ Temperature accuracy ±2℃ or ±2% (whichever is greater) Temperature resolution 0.1℃/0.18℉ Thermal resolution 320×240 Temperature coefficient ± 0.1/℃ or ± 0.1%/℃ (whichever is greater) Visible light resolution 640×480 Emissivity Adjustable (0.01-1.00), 0.98 in default Reflectivity Reflectivity correction (adjustable background temperature) Palettes White hot, iron red, arctic, rainbow 2, hot iron, rainbow 1 High/low temperature tracking √ High/low temperature alarm √ Image blending/Picture in picture √ WIFI mode Connects to PC software and moblie phone App Lens 7mm Focus Focus free FOV 42.5°×32.5° NETD ≤60mK Image frequency 50Hz Digital zoom ×2, ×4 General Characteristics Power 7.4V 2300mAh Li-ion battery Display 3.5-inches TFT LCD Product color Red and grey Product net weight 1.8kg (Package) Product size 258mm x 98mm x 90mm Standard accessories Li-on battery x 2, USB power supply with multi plugs,
wrist strap, adaptor×5, SD card, USB cable, PC software CDStandard individual packing Gift box, tool box, English manual Standard quantity per carton 1pcs Standard carton measurement 410mm x 265mm x 180mm Standard carton gross weight 2.2kg SKU: n/a -
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a
There are no reviews yet.