- Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
₨5,264 ₨5,923
Weight | 0.7 kg |
---|---|
Dimensions | 14 × 7 × 5 cm |
TITAN BATTERY TESTER BT 100 A CAN BE USED TO TEST 6V AND 12 BATTERY SYSTEMS.IT CAN GENERATE LOAD JUNK LOAD UPTO 90A DC.UPTO 200A BATTERIES CAN BE TESTED.
1 x BT 100 A
1 x MANUAL
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100A”
-
Battery Testers
UNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Battery TestersUNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Model UT3513 Resistance range 20m Q/200m Q/2Q/20Q /200 Q/2kQ/20kQ Resolution 1 u Q/10 u Q/100 u Q/lmO/lOmQ/lOOmQ/1 Q/10Q/100Q Test current 1A/1A/100mA/10mA/1mA/1mA/100 uA/10 u A/l uA Testing terminal opencircuit voltage <1V/<1V/<1V/<1V/<5V/<5V/<5V/<5V/<3V/ Measured parameter DC resistance Basic accuracy Slow: 0. 1%; Medium: 0. 2% Maximum reading 22000 Range mode Auto/Manual/nominal Calibration Short-circuit full range zeroing Sorting function 3types of resistance and voltage input: exceeds upper limit/exceeds lower limit/within the range,2 types of sorting result output: PASS/FAIL Comparing method Absolute tolerance, percentage tolerance, direct-reading comparison Trigger mode Internal, external Test terminal Four-terminal measurement Button functions Lock 一一 keyboard lock, OK 一一 screenshot System setup Language: Chinese/English, key tone setting Interfaces & protocols Handler interface, RS232, USB DEVICE and USB HOST communication interface,SCPI and Modbus protocol Upper computer software V Power AC 100~240V 50/60Hz Display 4.3-inches LCD SKU: n/a -
Oscilloscopes
UNI-T MSO3254E 250MHz Mixed Signal 4 Channel Digital Oscilloscope
Analog bandwidth 150MHz 250MHz Channels 2+16 digital 4+16 digital 2+16 digital 4+ 16digital Sampling rate (Analog) 2.5GS/s (Single channel), 1.25GS/s (Dual channels) Sampling rate (Digital) 1.25GS/s (Eight channels), 625MS/s(Sixteen channels) Memory depth 70Mpts Waveform capture rate 200,000wfms/s Time base scale 2ns/div~50s/div (Real-time sampling rate, memory depth display ) Time base scale (digital) 2ns/div~40S/div[Step by 1-2-4 stall] Input impedance (1MΩ±1%) II (20pF±3pF) Input impedance digital (101kΩ±1%) II (9pF±1pF) Vertical scale 1mV/div~20 V/div (1 MΩ) DC gain accuracy <5mV: ±3%, ≥5mV: ±2% Waveform record 100,000 frames Trigger types Edge, Runt, Window, Nth Edge, Delay, Overtime, Duration, Setup/Hold, Pulse Width, Slop, Video, Code; RS232/UART, I2C, SPI, USB,
CAN, LIN, FlexRayBus decode RS232/UART, I2C, SPI, USB, CAN, LIN, FlexRay Waveform operations A+B, A-B, A×B, A/B, FFT, editable advanced and logical operations Auto measurements
Max, Min, High, Low, Ampl, Pk-Pk, Middle, Mean, CycMean, RMS, CycRMS, Period, Freq, Rise, Fall, RiseDelay, FallDelay, +Width,
-Width, FRR, FRF, FFR, FFF, LRF, LRR, LFR, LFF, +Duty, -Duty, Area, CycArea, OverSht, PreSht, Phase, 34 parameters in totaldigital
channel: Freq, Period, +Width, -Width, +Duty, -Duty, RiseDelay A→B,FallDelay A→B, Phase A→B, Phase B→AMeasurement display 5 types Measurement statistics Average, Max, Min, standard deviation and number of measurements Frequency counter 6 bits Standard interfaces USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail), AWG,UT-M15 logic analyzer probe, VGA Standard Accessories
USB interface cable UT-D14 Passive Probe x 2/4 (1 x , 10 x switchable,300MHz,) UT-P06 Passive Probe x 2/4 (1 x , 10 x switchable,200MHz,) UT-P05 16CH Logic analyzer probe UT-15M SKU: n/a -
Clamp Meters
CLAMP METER AC DC ET 8203
Descriptions:
1.This is a 5999 counts automatic digital clamp multimeter,small and compact design for easy carrying.
2.Stable performance,high precision,high reliability,clear reading and overload protection.
3.It is a ideal tool and instrument,laboratory,factory,radio enthusiasts and The ideal tool for the family.Specifications:
Brand:WINAPEX
Model: 8203
Color:Black
Jaw:40mm
Maximum display:5999
DC Voltage: 6V/60V/600V/1000V
AC Voltage: 6V/60V/600V/750V
AC Current: 60A/600A
DC Current: 60A/600A
Resistance(ohm):600Ω/6KΩ/60Ω/600KΩ/6MΩ/40MΩ
Capacitance:60nF/600nF/6uF/60uF/600uF/6mF/30mF
Frequency:10Hz/100Hz/1kHz/10Hz/100Hz/1MHz/10MHz
Temperature:(-20-1000 )℃/(0-1832 )℉
DC voltage DCV :yes
AC voltage ACV :yes
AC current ACA :yes
DC current DCA :yes
T-RMS:yes
NCV:yes
Square wave output:yes
On-Off Test :yes
Diode measurement:yes
Buzzer:yes
Zero line / Fire line test :yes
Data hold:yes
Material: Plastic, Electronic Parts
Battery: 2 x 1.5V AAA Batteries (not included)
Product size:176x67x33mm/6.86×2.61×1.29in
Product weight:305g/10.68ozPackage information:
Package weight:350g/12.25oz
Package size:210x80x35mm/8.19×3.12×1.37in
General Box PackagePackage included:
1 x Clamp Meter
1 x Pair of test leads
1 x Thermocouple
1 x User ManualNoted:
1.Cannot measure,there is no current through the ground wire,can only be measured as a single wire or zero Iine.
2.Cannot measure two or more lines at the same time.
3.A line contains two or more than two wire core can not be measured.SKU: n/a
There are no reviews yet.