The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Tool Kits
JM 8170 TOOL KIT
21 in 1 screwdriver has a metal case and a surface matte treatment with the textured and laser typing logo Jakemy to highlight the taste. Open the 21 in 1 screwdriver simply by clicking the pop-up button that can be used with one hand. Its lightweight and convenient design make it easy to carry. JM-8170 21 in 1 screwdriver has 20 kinds of bits with 20n ways to play.
SKU: n/a -
Insulation Tester
JM Z16 HEAT INSULATION MAT
JAKEMY JM-Z16 Magnetic Heat Insulation Silicone anti-static Working Mat for Soldering Assembling Electronics DIY Repair.
Feature:
Brand new and high quality.
Heat-resistant coefficient: 300 Celcius degree (hot wind) / 230 Celcius degree (direct contact).
Anti-static coefficient: 1*10E12ohm.
Units design, easy to keep track of parts.
Food grade material, non-toxic and safe in use. 6. Suitable for electronics devices repairing.Accessories:
Anti-static and heat-proof working mat*1SKU: n/a
There are no reviews yet.