Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Tool Kits
JM Y01 TOOL KIT
Features:
- Low-key and luxurious at the same time.
- The shell goes through 10 parts of complicated procedures and 550°C of high temperature point injection.
- You can feel a skin-friendly feeling in this electric screwdriver.
- This electric screwdriver can work in 1.5 hours of full-loaded condition or 3-4 hours of no-loaded condition.
- Can duration of 90 days, which can be charged with 220V ac for 1.5 hours, with 5V USB voltage for 4 hours.
- And can be illuminated in all directions with 4 LED downlight.
- It is omnipotent from small products to large products.
SKU: n/a -
Moisture Testers
UT377A Wood Moisture Meter
UT377A is a digital meter designed to measure the moisture content of wood, paper, plywood, and other wooden materials. This device classifies wood into four categories based on material density, and applies temperature compensation algorithm to ensure measurement accuracy. UT377A’s miniature design, low power consumption, and high precision all make this a great product choice for measuring wood moisture content.
SKU: n/a -
Multimeters
UT81C Scope Digital Multimeter
UT81 series handheld digital oscilloscope multimeters combine oscilloscope and digital multimeter in one. Oscilloscope measurement mode includes signal input, data processing, auto measure, waveform storage, and transfer.
Multimeter mode features AC/DC voltage and current, resistance, diode, continuity, frequency, duty ratio, and capacitanceSKU: n/a
Related products
-
Battery Testers
UNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Battery TestersUNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Model UT3513 Resistance range 20m Q/200m Q/2Q/20Q /200 Q/2kQ/20kQ Resolution 1 u Q/10 u Q/100 u Q/lmO/lOmQ/lOOmQ/1 Q/10Q/100Q Test current 1A/1A/100mA/10mA/1mA/1mA/100 uA/10 u A/l uA Testing terminal opencircuit voltage ＜1V/＜1V/＜1V/＜1V/＜5V/＜5V/＜5V/＜5V/＜3V/ Measured parameter DC resistance Basic accuracy Slow: 0. 1%; Medium: 0. 2% Maximum reading 22000 Range mode Auto/Manual/nominal Calibration Short-circuit full range zeroing Sorting function 3types of resistance and voltage input: exceeds upper limit/exceeds lower limit/within the range,2 types of sorting result output: PASS/FAIL Comparing method Absolute tolerance, percentage tolerance, direct-reading comparison Trigger mode Internal, external Test terminal Four-terminal measurement Button functions Lock 一一 keyboard lock, OK 一一 screenshot System setup Language: Chinese/English, key tone setting Interfaces & protocols Handler interface, RS232, USB DEVICE and USB HOST communication interface,SCPI and Modbus protocol Upper computer software V Power AC 100~240V 50/60Hz Display 4.3-inches LCD SKU: n/a -
Battery Testers
UT675A Battery Testers
Features of UT675A Battery Testers
Certifications: CE, UKCA, FCC
● 12V cranking lead acid battery test
● 12/24V charging or cranking system test● Display battery capacity, voltage, resistance and life● Four-termina Kelvin test● 10 types of battery standards● Language option (Chinese/English)● Test without battery disassembly● LED color indication for test result (UT673A)● Print on-line and real-time test reports (UT675A)● USB data transfer (UT675A)SKU: n/a
There are no reviews yet.