-
×
SOLDERING IRON WJ 30WATT
- Vendor:
superworld
Subtotal: ₨450
-8%
Clamp Meters
CMP-1006 Digital Clamp-on multimeter
Availability:
5 in stock
Additionally:
- safe, insulated measuring clamps,
- autoranging/manual range selection,
- DATA HOLD function, for holding measured values,
- backlit LCD,
- DC ZERO mode of measurement for DC current, possibility to zero the display and reading relative actual value less stored zero value,
- MAX/MIN function,
- over range indication,
- AUTO-OFF function.
₨31,587 ₨34,221
5 in stock
Compare(TRUE RMS) up to 1000 A.
Measurement of INRUSH current in start-up phase of electrical device (high frequency of sampling)
AC/DC voltage measurement (TRUE RMS) up to 600 V.
Resistance measurement and continuity test:
- continuity test with acoustic signalling (beeper) for resistance below 40.
Temperature measurement (Fahrenheit and Celsius units).
Frequency measurement.
Duty cycle measurement.
Diode test.
| Weight | 0.3 kg |
|---|---|
| Dimensions | 23 × 8 × 5 cm |
Electric security:
- measurement category: CAT III 600 V acc. to EN 61010 – 1:2004
- protection class acc. to EN 60529: IP40
Other technical data:
- power supply: 9 V battery type 6LR61
- display: 6600 counts, backlit LCD
- continuity test: threshold 40 Ω; test current < 0,5 mA
- diode test: test current of 0,3 mA, typical open circuit voltage < 3 V DC, typical
- low battery indication: BAT displayed
- over range indication: 0L displayed
- sampling rate: 2 times per second
- INRUSH: integration time 100 ms
- temperature sensor: type K thermocouple
- input impedance: 10 MΩ (V DC and V AC)
- AC bandwidth: 50…400 Hz (A AC and V AC)
- auto power OFF: approx. 25 min.
- dimensions: 229 x 80 x 49 mm
- weight: 303 g
- accordance with following standards: EN 61010 – 1:2004, EN 61010 – 2 – 032
- quality standard: ISO 9001
Rated operational conditions:
- internal clamp diameters: d1 = 36 mm/d2 = 52 mm
- operating temperature: +5…+40°C
- storage temperature: -20…+60°C
- operating humidity: max 80% up to 31°C decreasing linearly to 50% at 40°C
- storage humidity: <80%
- operating altitude: max 2000 m
AC/DC current measurement (TRUE RMS)
| Range | Resolution | Accuracy (DC) | Accuracy (AC) |
|---|---|---|---|
| 0…659,9 A | 0,1 A | ±(2,5% m.v. +5 dgt) | ±(2,5% m.v + 8 dgt) for f = 50…60 Hz |
| 660…1000 A | 1 A | ±(2,8% m.v. +8 dgt) | ±(2,8% m.v. + 8 dgt) for f = 50…60 Hz |
DC voltage measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 0…6,599 V | 0,001 V | ±(1,5% m.v. + 3 dgt) |
| 6,60…65,99 V | 0,01 V | ±(1,5% m.v. + 3 dgt) |
| 66,0…600,0 V | 0,1 V | ±(1,5% m.v. + 3 dgt) |
AC voltage measurement (TRUE RMS)
| Range | Resolution | Accuracy |
|---|---|---|
| 0…6,599 V | 0,001 V | ±(1,8% m.v. + 5 dgt) for f = 50…60 Hz |
| 6,60…65,99 V | 0,01 V | ±(1,8% m.v. + 5 dgt) for f = 50…60 Hz |
| 66,0…600,0 V | 0,1 V | ±(1,8% m.v. + 5 dgt) for f = 50…60 Hz |
Resistance measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 0,0…659,9 Ω | 0,1 Ω | ±(1,0% m.v. + 4 dgt) |
| 0,660…6,599 kΩ | 0,001 kΩ | ±(1,5% m.v. + 2 dgt) |
| 6,60…65,99 kΩ | 0,01 kΩ | ±(1,5% m.v. + 2 dgt) |
| 66,0…659,9 kΩ | 0,1 kΩ | ±(1,5% m.v. + 2 dgt) |
| 0,660…6,599 MΩ | 0,001 MΩ | ±(2,5% m.v. + 3 dgt) |
| 6,60…66,00 MΩ | 0,01 MΩ | ±(3,5% m.v. + 5 dgt) |
Frequency measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 30,0…999,9 Hz | 0,1 Hz | ±(1.2% m.v. + 2 dgt) sensitivity:30…5 kHz:10 Vrms min. 5 kHz…15 kHz:40 Vrms min. for 20%…80% duty cycle |
| 1,000…9,999 kHz | 0,001 kHz | ±(1.2% m.v. + 2 dgt) sensitivity:30…5 kHz:10 Vrms min. 5 kHz…15 kHz:40 Vrms min. for 20%…80% duty cycle |
| 10,00…15,00 kHz | 0,01 kHz | ±(1.2% m.v. + 2 dgt) sensitivity:30…5 kHz:10 Vrms min. 5 kHz…15 kHz:40 Vrms min. for 20%…80% duty cycle |
Temperature measurement
| Range | Resolution | Accuracy |
|---|---|---|
| -20…760°C | 0,1°C | ±(3,0% m.v. + 5°C) |
| -4…1400°F | 0,1°F | ±(3,0% m.v. + 9°F) |
Duty cycle measurement
| Range | Resolution | Accuracy |
|---|---|---|
| 10,0…94,9% | 0,1% | ±(1,2% m.v. + 2 dgt) |
- pulse width: 100μs…100 ms,
- frequency range: 30 Hz…5 kHz,
- sensitivity: 30 Hz…5 kHz: 10 Vrms, 5 kHz…15 kHz: 40 Vrms.
„m.v.”- measured value
Brand
SONEL
Based on 0 reviews
Be the first to review “CMP-1006 Digital Clamp-on multimeter”
-
Dc Veriable Loads
UNI-T UTL8211/UTL8212 High-Precision Compact DC Electronic Load Tester Single/Dual Channel 150V Power Supply Current Test – UTL8211
Dc Veriable LoadsUNI-T UTL8211/UTL8212 High-Precision Compact DC Electronic Load Tester Single/Dual Channel 150V Power Supply Current Test – UTL8211
Application:
Power supply test, adapter/charger test, battery test, lithium battery protection board test, ATE, component test, etc., commonly used in home appliance manufacturers, LCD and other computer component manufacturers, switching power supply and LED manufacturers, adapter charger manufacturers and other companies Production and testing use
SKU: n/a -
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
Related products
-
Clamp Meters
UT 208 CLAMP METER
1. 1000A AC/DC current measurement, 3 times/s sampling rate
2. True RMS3. Inrush current4. Zeroing function5. Full icon display6. MAX/MIN7. Data hold; Duty cycle8. Auto power off and low battery indication9. Point contact temperature probe10. Diode; Continuity buzzer; Input Impedance for DCVSKU: n/a -
Clamp Meters
MT87 3 1/2 Digits LCD Digital Clamp Meter
This meter features a portable design, 31/2 LCD display and 25mm jaw opening, which can provides various measurements for AC/DC voltage, AC current, resistance, diode and continuity buzzer. It is also with functions of date hold, low battery indication, overload indication, etc. More detailed product information, please refer to the English manual.
SKU: MT 87 CLAMP METER -
Clamp Meters
UT216A 600A Digital Clamp Meters
UT216 series true RMS digital clamp meter is a new-generation practical electrotechnical measurement meter which has the features of high reliability, high safety, automatic range and handheld type, has full-range overload protection and unique appearance design, is more excellent in performance, and is an ideal tool for detection, maintenance and repair of various universities and colleges, smelting, communication, manufacturing, petroleum, national defense, electrical, power and circuit equipment.
UTD216A (main features)- 1、600A AC current measurement
- 2、True RMS response for ACV and ACA
- 3、99.99mF capacitance measurement
- 4、Non-contact voltage detection with LED indication
- 5、Flashlight for working at dark environment
SKU: n/a -
Clamp Meters
UT219DS ACA DCA Professional Clamp Meters with Motor LPF Test
- UT-219 professional clamp meter series is three-proofing digital clamp meter specially designed for professional industrial users.
- The industrial design of this series is rugged and durable, and capable of withstanding the impact from 2 meters fall-down.
- The waterproof rating is up to IP54; therefore, it can be used in environment with water splashing or much more dust.
- The whole series is configured with LoZ (Low Impedance Input) AC voltage tap position, which is capable of testing the false voltage; auto backlight function can be used continuously under the circumstance of emergency power outage.
- UT-219DS is also provided with MOTOR test function, allowing to directly test the phase sequence of three phase AC motor by means of the probe. UT-219 series is much more in compliance with CAT IV 600V safety level, and certified by the German GS institution.
SKU: n/a
There are no reviews yet.