- Detection of wires and cables (live or not)
- detection of cables in ceilings, walls and floors,
- detection of breaks in cables,
- tracing cables in building installation,
- locating power points and switches in buildings,
- locating short circuits between leads,
- tracing shielded cables,
- tracing cables in metal ducts.
- Identification of fuses on the distribution board.
- Tracing underground cables.
- Tracing conductive water and heating pipelines.
- Non-contact detection of live cables.
LKZ-720 Wires and pipe locator
2 in stock
Features:
- the function 3D in the receiver – detecting the direction of current flow and accurate locating the object,
- phase detection mode,
- receiver operation with four transmitters at the same time to locate interruptions or distinguish wires,
- a LED bright torch,
- headphone socket in receiver,
- screens backlight for work in dark,
- transmission battery status and settings of the transmitter to the receiver
- operation in wide range of rated voltage, up to 500V RMS,
- measurement of voltage at the object to 500 Vrms,
- three levels of transmitter amplification,
- automatic or manual selection of transmitter operation modes,
- five modes of wire tracer operation – voltage, current, current-voltage, power and clamp,
- software upgrade via USB,
- additional accessories enable precise localization – such as contact or non-contact probes and measurement clamp.
₨200,000 ₨210,000
2 in stock
CompareElectric security:
- type of insulation: double, according to EN 61010-1
- measurement category: CAT III 600V acc. to EN 61010-1
- transmitter’s protection class acc. to EN 60529: IP67
- receiver’s protection class acc. to EN 60529: IP40
Other technical data:
- transmitter’s power supply: four AA alkaline battery or NiMH rechargeable battery
- transmitter’s max working voltage: 500 Vrms (707 Vampl)
- detector’s max range („I” mode) 2m
- non-contact neon max range: 20 cm (in air), 3 cm (in concrete)
- receiver’s power supply: battery 9V 6LR61 alkaline
Rated operational conditions:
- operating temperature -10°C…+50°C
Based on 0 reviews
Be the first to review “LKZ-720 Wires and pipe locator”
-
Clamp Meters
MS 2109A ACA DCA Digital Clamp Meters
● Display 6000 counts
● Jaw Opening Ф26mm/1.0″
● Auto Ranging
● Auto Power Off
● Non-Contact Voltage Detector
● Relative Measurement
● Diode Open Volatge 2.7V
● Continuity Buzzer <50±20Ω
● MAX/MIN
● Data Hold
● Display Backlight
● Work Light
● Low Battery DisplaySKU: n/a -
Clamp Meters
UT219E ACA Professional Clamp Meters
Features
1. 2m drop proof, IP54, CAT IV 600V
2. Large 6000-digit LCD backlight (auto) display
3. True RMS
4. LoZ voltage test, for ghost voltage measurement
5. MAX/MIN/REL testing mode, data hold, excluding the test lead interference of resistance measurement
SKU: n/a -
Clamp Meters
UT256B ACA DCA Fork Clamp Meters
UT256 series is an AC/DC fork meter with high reliability, high security, auto-range, and mini shape. Its appearance adopts creative design so that wires to be tested can be stuck by the jaw directly instead of after the jaw is pressed to open. It can measure AC/DC current provided with true RMS function. Flashlight on the meter is specially designed for smooth measurement under darkness. Full-range overload protection and distinctive appearance design make it be a new-generation practical electrical measuring meter with better performance.
SKU: n/a -
Welding Machine
Mechanic W08 Portable Mini Battery Welder Spot Welding Machine
1. W08 Mini Precision Spot Welding Machine Suitable for precision welding of mobile phone electronic components, battery plate replacement, lithium battery nickel sheet, etc.
2. W08 portable spot welder uses a high-multiplier lithium battery as the power supply, mainly used for welding of nickel sheets of cylindrical batteries. This W08 DIY soldering machine can be used to solder the battery protection board when replacing the battery.SKU: n/a -
Leeb Hardness Tester
UT347A Leeb Hardness Tester
Features of UT347A Leeb Hardness Tester
Certificates: CE (In processing), UKCA
● 6 kinds of hardness values (HL, HB, HRC, HRB, HV, HS) is a real-time measurement
● One hardness tester can be equipped with 7 different impact devices● Automatic identification without calibration when replacing impact device
● Statistical, multi-unit, line chart, histogram 4 measurement modes
● Camera: 640×480 pixels (900 BMP format pictures could be stored)● Automatic alarm when the upper and lower limits are exceeded● Adjustable backlight brightness● Mobile phone Bluetooth APP and PC software analysis data● Support thermal printing● Tri-color LED indication and LED flashlightSKU: n/a
There are no reviews yet.