LKZ-720 Wires and pipe locator
2 in stock
Features:
- the function 3D in the receiver – detecting the direction of current flow and accurate locating the object,
- phase detection mode,
- receiver operation with four transmitters at the same time to locate interruptions or distinguish wires,
- a LED bright torch,
- headphone socket in receiver,
- screens backlight for work in dark,
- transmission battery status and settings of the transmitter to the receiver
- operation in wide range of rated voltage, up to 500V RMS,
- measurement of voltage at the object to 500 Vrms,
- three levels of transmitter amplification,
- automatic or manual selection of transmitter operation modes,
- five modes of wire tracer operation – voltage, current, current-voltage, power and clamp,
- software upgrade via USB,
- additional accessories enable precise localization – such as contact or non-contact probes and measurement clamp.
₨200,000 ₨210,000
2 in stock
Compare- Detection of wires and cables (live or not)
- detection of cables in ceilings, walls and floors,
- detection of breaks in cables,
- tracing cables in building installation,
- locating power points and switches in buildings,
- locating short circuits between leads,
- tracing shielded cables,
- tracing cables in metal ducts.
- Identification of fuses on the distribution board.
- Tracing underground cables.
- Tracing conductive water and heating pipelines.
- Non-contact detection of live cables.
Electric security:
- type of insulation: double, according to EN 61010-1
- measurement category: CAT III 600V acc. to EN 61010-1
- transmitter’s protection class acc. to EN 60529: IP67
- receiver’s protection class acc. to EN 60529: IP40
Other technical data:
- transmitter’s power supply: four AA alkaline battery or NiMH rechargeable battery
- transmitter’s max working voltage: 500 Vrms (707 Vampl)
- detector’s max range („I” mode) 2m
- non-contact neon max range: 20 cm (in air), 3 cm (in concrete)
- receiver’s power supply: battery 9V 6LR61 alkaline
Rated operational conditions:
- operating temperature -10°C…+50°C
Brand
SONEL
Based on 0 reviews
Be the first to review “LKZ-720 Wires and pipe locator”
-
-
Clamp Meters
CLAMP METER AC BM 528F
Product DescriptionBM528F AC Digital Clamp meter Technical parametersFunctionsRangeAccuracy(BM528F)DC Voltage200mV/2V/20V/200V/1000V±（0.8%+2）AC Voltage2V/20V/200V/700V±（1.2%+5）AC Current2A/20A/200A/600A±（2%+10）Ω Resistance200/2K/20K/200K/2M/20MΩ±（1%+3）Capacitance20n/200n/2μ/20μ/200μ/2mF±（3%+5）Frequency200/2K/20K/200K/2M/20MHz±（0.5%+3）℃ / ℉-50℃ ~1000℃-58℉~1832℉
±（1%+5）±（1.2%+6）SKU: n/a -
IR Thermo Meters
UNI-T UTi260E Professional Handheld IR Thermal Camera 256×192 pixels Wide Temperature -20ºC~550ºC with PC,WiFi,App Real Time Display
IR Thermo MetersUNI-T UTi260E Professional Handheld IR Thermal Camera 256×192 pixels Wide Temperature -20ºC~550ºC with PC,WiFi,App Real Time Display
UTi260B
Motor inspection:
Using UNI-T thermal imager can detect the imbalance loading, overloading, wiring error and parts malfunction etc. Heat insulation protection is the key action for avoid fire risk, engineer can also use the thermal imager check the protection situation regularly to ensure the safety production.PCBA inspection:
Using UNI-T thermal imager can quickly locate the components where temperature is abnormally higher.Electric inspection:
Using UNI-T thermal imager to check the device temperature can find the problems in time on switcher, contactor, transformer etc, which maybe caused by oxidation, corrosion, poor contact.SKU: n/a
Related products
-
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
-
Wire & Cable Testers
LKZ-1000 Wires and pipe locator
- Passive or active modes of tracing.
- Detection of underground live wires.
- Detection of underground wires with no voltage (radio mode).
- Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).
- Tracing metallic or non-conductive pipes using an additional probe.
- Tracing non-conductive pipelines using a “floating” probe.
- Tracing a determined cable.
- Determining the depth of a cable.
SKU: n/a -
Wire & Cable Testers
UT682 – Wire Tracker
UT682 – Wire Tracker consists of a transmitter and a receiver. It has functions like telephone wire tracking, network wire tracking, cable wire tracking, network wire check, etc. and it produces fast and accurate measurements. UT682 is an ideal tool for personnel to install and maintain network systems with communication lines and integrated wiring circuits.
SKU: n/a -
Wire & Cable Testers
UTP 03 60MHZ PROBE
Attenuation ratio: 1× and 10× optional.
Portable design according to ergonomics.
Integral injection moulding makes the usage more flexible and the oscillograph able to adapt more testing situations.
Safety standards: it has passed the CE Attestation of the European Community.
Compatible with domestic and international digital and analogue oscilloscopes in relevant frequency.
Measurement in intermediate and low-frequency signals.
Accessories included by PP series passive voltage rapier.
Adjusting tool: adjusts compensation capacitance to assure the rapier match with oscillograph.
Contractive-type acuminate hook.
12cm earth wire with an alligator clip.
Locating sleeve adapts to IC testing.
Double-nip wire.
SKU: n/a
There are no reviews yet.