-5%
Wire & Cable Testers
LKZ-720 Wires and pipe locator
Availability:
2 in stock
Features:
- the function 3D in the receiver – detecting the direction of current flow and accurate locating the object,
- phase detection mode,
- receiver operation with four transmitters at the same time to locate interruptions or distinguish wires,
- a LED bright torch,
- headphone socket in receiver,
- screens backlight for work in dark,
- transmission battery status and settings of the transmitter to the receiver
- operation in wide range of rated voltage, up to 500V RMS,
- measurement of voltage at the object to 500 Vrms,
- three levels of transmitter amplification,
- automatic or manual selection of transmitter operation modes,
- five modes of wire tracer operation – voltage, current, current-voltage, power and clamp,
- software upgrade via USB,
- additional accessories enable precise localization – such as contact or non-contact probes and measurement clamp.
₨200,000 ₨210,000
2 in stock
Compare- Detection of wires and cables (live or not)
- detection of cables in ceilings, walls and floors,
- detection of breaks in cables,
- tracing cables in building installation,
- locating power points and switches in buildings,
- locating short circuits between leads,
- tracing shielded cables,
- tracing cables in metal ducts.
- Identification of fuses on the distribution board.
- Tracing underground cables.
- Tracing conductive water and heating pipelines.
- Non-contact detection of live cables.
Electric security:
- type of insulation: double, according to EN 61010-1
- measurement category: CAT III 600V acc. to EN 61010-1
- transmitter’s protection class acc. to EN 60529: IP67
- receiver’s protection class acc. to EN 60529: IP40
Other technical data:
- transmitter’s power supply: four AA alkaline battery or NiMH rechargeable battery
- transmitter’s max working voltage: 500 Vrms (707 Vampl)
- detector’s max range („I” mode) 2m
- non-contact neon max range: 20 cm (in air), 3 cm (in concrete)
- receiver’s power supply: battery 9V 6LR61 alkaline
Rated operational conditions:
- operating temperature -10°C…+50°C
Brand
SONEL
Based on 0 reviews
Be the first to review “LKZ-720 Wires and pipe locator”
-
Tools and Hardware
JM OP06 OPENING TOOL
DescriptionItem Description:- Features:
– Stainless steel material make it more durable.
– Anti-corrosion with stainless steel forged process.
– Easier to disassemble the electronic part accessories.
– Common used in laptops, mobiles and tablets disassembling.
– Special rolling-wheel design for better use in opening.
– The end of the tool with anti-slip design make it easier for disassembling.
– Precision processing technology on the metal part for better protection on the product itself. - Brand: JAKEMY
- Model: JM-OP06
- Material: Stainless steel
- Color: Orange & silver
- Package Weight: 45.0 G / 1.59 Ounces
- Package Dimensions (L*W*H): 180*80*13 MM / 7.09*3.15*0.51 Inches200
SKU: n/a - Features:
-
Analog Multimeters
ANALOG METER YX 360TR BS
Features Of Handheld YX-360TRE-B Analog Meter Voltmeter:
- High accuracy analogue multimeter for general purposes.
- Mirrored needle indicator with an accurate reading.
- Check both AC and DC parameters with continuity buzzer on Ohms.
- Up to 1000V on both AC and DC Voltage.
- 19 versatile ranges for general-purpose testing.
- Fuse & Diode protection.
- Compact sizing.
- Tilt back-stand.
- The large and mirrored scale of 80mm length.
SKU: n/a -
Multimeters
UNI T Bench Top Digital Multimeter UT8803E
- 20,000 Count EBTN LCD Display
- DC Voltage: 200mV/2V/20V/200V/1000V
- AC Voltage: 2V/20V/200V/750V
- DC Current: 200μA/2mA/20mA/200mA/20A
- AC Current: 2mA/20mA/200mA/20A
- Resistance: 200Ω/2kΩ/20kΩ/200kΩ/2MΩ/200MΩ
- Capacitance: 20nF/200nF/2μF/20μF/200μF/2mF/20mF/100mF
- Frequency: 200Hz~10MHz
- Duty cycle: 5%~99%
- Frequency response: 1 kHz
- USB Interface
- Data hold
- MAX/MIN
- Continuity buzzer
- Diode/transistor
- test
- CAT II 600V
SKU: n/a -
Related products
-
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
-
Wire & Cable Testers
MS6812 Cable Tracker
The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker
● Sound and Light Instruction
● Cont and Tone LED LightApplications
– Judge Continuity of the Cables or Wires
– Track the Cables or Wires, and Diagnose the Break Point
– Receive the Tone Signal on the Cables or Wires(Telephone Line)
– Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
– Send a Single Solid or a Dual Alternating Tone to the Target Cables or WiresSKU: n/a
There are no reviews yet.