MRU-21 Earth Resistance Meter
2 in stock
Possible measurements:
- earth resistance measurment with 3-pole method,
- measurement of continuity of equipotential bondings and protective conductors with auto-zero function – with current 200 mA,
- resistance measurement using 2-pole method.
₨0
2 in stock
CompareEarth Resistance Meter
| Weight | 1.4 kg |
|---|---|
| Dimensions | 29 × 22 × 7 cm |
Measurement of earthing resistance
measurement range to IEC61557 – 5:
0,50 Ω…1,99 kΩ for Un=50 V;
0,68 Ω…1,99 kΩ for Un=25 V;
| Range | Resolution | Accuracy |
| 0,00…9,99 Ω | 0,01 Ω | ±(2% m.v. + 3 digits) |
| 10,0…99,9 Ω | 0,1 Ω | |
| 100…999 Ω | 1 Ω | |
| 1,00k…1,99 kΩ | 0,01 kΩ |
• measurement current: under short circuit >20 mA,
• voltage on open terminals: selectable <25 V AC or <50 V AC,
• frequency of measurement current: 125 Hz
Measurement of interference voltage UN (RMS)
| Range | Resolution | Accuracy |
| 0…100 V | 1 V | ±(2% m.v. + 3 digits) |
• measurement for DC and AC 45…65 Hz
Measurement of resistance of auxiliary electrodes RH i RS
| Range | Resolution | Accuracy |
| 0…999 Ω | 1 Ω | ±(5% (RS+RE+RH) + 3 digits) |
| 1,00k…9,99 kΩ | 0,01 kΩ | |
| 10,0k…50,0 kΩ | 0,1 kΩ |
Measuremet of continuity of equipotential bondings and protective conductors
measurement range to IEC61557 – 4: 0,13 Ω…199 Ω
| Range | Resolution | Accuracy |
| 0,00…9,99 Ω | 0,01 Ω | ±(2% m.v. + 3 digits) |
| 10,0…99,9 Ω | 0,1 Ω | |
| 100…199 Ω | 1 Ω |
- measuring method: technical 2-pole method,
- max. voltage on open terminals: 13 V,
- measurement current: under short circuit >200 mA,
- auto-zero function for measurement leads
Electric security:
- type of insulation: double, according to EN 61010 – 1and IEC 61557
- measurement category: CAT IV 300 V acc. to EN 61010 – 1
- protection class acc. to EN 60529: IP54
Rated operational conditions:
- operation temperature: -10…+55°C
- storage temperature: -20…+70°C
- humidity: 20…80%
Other technical data:
- LCD display: segment, backlit
- interface: USB,
- number of measurements carried out of set of batteries: > 1000 (5 Ω, 2 meas./min.)
- warranty: 2 years
- dimentions: 288 x 223×75 mm
- weigth: 1,4 kg
Brand
SONEL
Based on 0 reviews
Be the first to review “MRU-21 Earth Resistance Meter”
-
Clamp Meters
CMP-2000 Digital clamp-on multimeter
It provides:
- AC current measurement (TRUE RMS) up to 1500 A and DC up to 2000 A.
- Measurement of INRUSH current in start-up phase of electrical device.
- AC voltage measurement (TRUE RMS) up to 750 V and DC up to 1000 V.
- Resistance measurement and continuity test:
– continuity test with acoustic signalling (beeper) for resistance below 30 Ω. - Capacitance measurement.
- Temperature measurement (Fahrenheit or Celsius).
- Frequency measurement.
- Duty cycle measurement.
- Diode test.
SKU: n/a -
Digital Multi Meter
18B WINHY DMM
Description
Features:
Multifunction:Can accurately measure AC/DC voltage, AC/DC current,resistance,capacitance,frequency,diode,LED test and continuity testing.
Portable Design:There is a back bracket for supporting multimeter,and also can collect test probe for your convenience.
Widely use:It’s perfect tool for the laboratory,factory and electricity.
Easy to Use & Clear to Read:With large LCD Backlight display,convenient to use and read.
More advantages:Auto power off,range,select,True RMS,data hold,over range indication and low voltage display.SKU: n/a -
Phase Detector Meters
TKF-12 Phase Sequence Tester
Phase sequence indication (direction of field rotation) in the power network with rated phase-to-phase voltage (120…690 V) AC by LED signalization.
Operation in the power network with frequency range 10…70 Hz.
Indication of the voltage presence in the particular phases by neon lamps signalization.
Power supply from the tested network (continuous operation to 15 minutes for max. voltage).
Protection against faulty indication of field rotation.SKU: n/a -
Clamp Meters
CMP-1006 Digital Clamp-on multimeter
Additionally:
- safe, insulated measuring clamps,
- autoranging/manual range selection,
- DATA HOLD function, for holding measured values,
- backlit LCD,
- DC ZERO mode of measurement for DC current, possibility to zero the display and reading relative actual value less stored zero value,
- MAX/MIN function,
- over range indication,
- AUTO-OFF function.
SKU: n/a
Related products
-
Earth Ground Resistance Testers
UT521 Earth Groud Testers
UT520 series earth resistance tester hasthe functions of backlight display, low battery display, data hold, datastorage, auto power off and power saving. It can not only be used for accurate three-wiremeasurement but also simple two-wire measurement.
It is applicable to measuring the earthresistance of all kinds of electrical power system, electrical equipment and anti-thunderequipment. It can also measure the earth voltage. It is applicable to testingoperating earth systems of smelting, communication, manufacture, fossil oil,national defense, electricity, chemical industry and construction.
SKU: n/a -
Earth Ground Resistance Testers
UT275 Clamp Earth Ground Testers
UT270 series can measure the grounding system of a circuit without disconnecting the ground wires and auxiliary electrode. It clamps the grounding circuit and measures the grounding resistance fast and safely. It can measure resistance as low as 0.01Ω and has a high resolution of 0.001Ω. It has overload alarm function, which can help to setup the alarm value within the ranges. The clamp has double insulation, which strengthens the anti-interference.
SKU: 90000 -
Earth Ground Resistance Testers
MRU-30 Earth Resistance and Resistivity Meter
-
It allows to take the measurements of:
- earthing resistance using auxiliary electrodes,
- earthing resistance using auxiliary electrodes and clamp (for measurements of multiple earthing),
- earthing resistance using double clamps for measuring multiple earthing without underground connections.
- ground resistivity (Wenner method),
- continuity of equipotential bondings and protective
- conductors (meeting the requirements IEC 60364) with auto-zero function – with current 200mA.
Additionally:
- measurement of resistance of auxiliary electrodes RS and RH,
- measurement of interference voltage,
- measurement in the presence of interference voltage in the power network
- with frequency 50Hz, 60Hz,
- selection of maximum measuring voltage (25V and 50V),
- introducing the distance between the electrodes for the resistivity in metres (m) and feet (ft),
- memory of 990 measurements (10 banks of 99 cells each),
- calibration of clamp used,
- data transmission to the computer (USB),
- indication of battery state.
SKU: n/a -
There are no reviews yet.