- Location damaged power cables.
- Fault location copper telecom cables.
- Coaxial cable fault location.
- Fault location wiring infrastructure.
- Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
- Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
TDR-410 Cable Fault Locator
Out of stock
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
₨0
Out of stock
CompareDechnical data:
- Ranges Meters: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
- Ranges Feet: 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 14000.
- Range Selection: Manual range control / Auto range.
- Accuracy: 1% of selected range*.
- Resolution: Approx 1% of range.
- Minimum cable lenght: 4m (14ft).
- Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP.
- Velocity Factor: Adjustable from 1% to 99%.
- Output Pulse: 5 volts peak to peak into open circuit.
- Output Impedance: Selectable 25, 50, 75 & 100 Ω.
- Output Pulse: Width 3 ns to 3 µs, Automatic with range.
- Scan Rate: 2 scans/second or scan held, pre set for each range scale.
- Tone Generator: 810 – 1100Hz.
- Battery Life: 30 hours continuous scanning.
- Power Supply: 6 volts 4 x 1.5 AA Alkaline cells, on-screen low voltage indicator.
- Power Down Selectable: 1, 2, 3, 5 minutes or disabled.
- Back Lit Display: 128 x 64 pixel.
- Voltage Protection: 250 volts AC.
- Operating Temp: -10º / 50ºC.
- Storage Temp: -20º +70° C.
- Dimensions: 165 x 90 x 37 mm (6.5 x 3.5 x 1.5 ins).
- Weight: 350 g (12oz).
- Safety: IEC 61010-1, EN 60950.
- EMC: BS/EN 61326-1.
- Water/Dust Proof: IP54
Based on 0 reviews
Be the first to review “TDR-410 Cable Fault Locator”
-
Oscilloscopes
UTD1025CL Handheld Digital Storage Oscilloscopes
Product Features:
1、 Fully Auto Scale; Vertical Scale and Timebase automatically adjusted with the signal and without any manual interference;
2、 Unique and powerful Auto Setup, quick and accurate to set up for signals with any DC component;
3、 Wider voltage measuring range; Coupled with 10×probe with attenuation up to 200V/div;
4、 Isolated USB for much safer communication;
5、 White and black display for your option, perfect for use outdoors with strong light;
6、 Intelligent local or network software update;
7、 More than 8hours of continuous battery operation.SKU: 80000 -
Multimeters
UNI T Bench Top Digital Multimeter UT8803E
- 20,000 Count EBTN LCD Display
- DC Voltage: 200mV/2V/20V/200V/1000V
- AC Voltage: 2V/20V/200V/750V
- DC Current: 200μA/2mA/20mA/200mA/20A
- AC Current: 2mA/20mA/200mA/20A
- Resistance: 200Ω/2kΩ/20kΩ/200kΩ/2MΩ/200MΩ
- Capacitance: 20nF/200nF/2μF/20μF/200μF/2mF/20mF/100mF
- Frequency: 200Hz~10MHz
- Duty cycle: 5%~99%
- Frequency response: 1 kHz
- USB Interface
- Data hold
- MAX/MIN
- Continuity buzzer
- Diode/transistor
- test
- CAT II 600V
SKU: n/a -
-
Multimeters
UT58A General Digital Multimeters
Product Features
1. 2,000 display count, 2~3/s sampling rate
2. Large 60mm×54mm LCD screen
3. Function symbols and test lead connecting indication for all ranges
4. Capacitance and transistor measurement
5. Diode and buzzer continuity
6. Data hold
7. Auto power off
8. 20A AC/DC current measurement
9. Complies with CE (European Union) directives
SKU: n/a -
Tool Kits
JM-TP03 Double Head Bits Set Screwdriver
Features:
- Set screwdriver
- Consists of 10 PZ2 type nut heads commonly used for electric screwdriver heads
- Equipped with a box to keep the screwdriver head with a lightweight design
- Has a very strong magnetic adhesive
- Material: Chrome vanadium
SKU: n/a
There are no reviews yet.