TDR-410 Cable Fault Locator
Out of stock
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
₨0
Out of stock
Compare- Location damaged power cables.
- Fault location copper telecom cables.
- Coaxial cable fault location.
- Fault location wiring infrastructure.
- Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
- Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
Dechnical data:
- Ranges Meters: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
- Ranges Feet: 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 14000.
- Range Selection: Manual range control / Auto range.
- Accuracy: 1% of selected range*.
- Resolution: Approx 1% of range.
- Minimum cable lenght: 4m (14ft).
- Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP.
- Velocity Factor: Adjustable from 1% to 99%.
- Output Pulse: 5 volts peak to peak into open circuit.
- Output Impedance: Selectable 25, 50, 75 & 100 Ω.
- Output Pulse: Width 3 ns to 3 µs, Automatic with range.
- Scan Rate: 2 scans/second or scan held, pre set for each range scale.
- Tone Generator: 810 – 1100Hz.
- Battery Life: 30 hours continuous scanning.
- Power Supply: 6 volts 4 x 1.5 AA Alkaline cells, on-screen low voltage indicator.
- Power Down Selectable: 1, 2, 3, 5 minutes or disabled.
- Back Lit Display: 128 x 64 pixel.
- Voltage Protection: 250 volts AC.
- Operating Temp: -10º / 50ºC.
- Storage Temp: -20º +70° C.
- Dimensions: 165 x 90 x 37 mm (6.5 x 3.5 x 1.5 ins).
- Weight: 350 g (12oz).
- Safety: IEC 61010-1, EN 60950.
- EMC: BS/EN 61326-1.
- Water/Dust Proof: IP54
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-410 Cable Fault Locator”
-
Usb Tester
UNI T UT658DUAL USB Tester
Features of UT658 Series USB Testers
Certifications: CE, UKCA
● Type-A/C interface
● CE certification
● 10 sets of data storage
● Loop equivalent resistance measurement (1-480Ω)
● Same screen shows voltage, current, power, capacity, etc.
● Support fast charge protocol
SKU: n/a -
Clamp Meters
UT281A True RMS AC 3000A Flexible Clamp Meters
1. 2m drop proof, IP54, ETL/Intertek certified 3rd edition CE
2. Coil diameter: 0.75cm, bending length: 24.5cm for UT281A and 45.7cm for UT281C
3. Large LCD display for clear reading
4. True RMS
5. Long press INRUSH key for 2s to measure inrush current
6. Data hold, backlight, auto power off
SKU: n/a
Related products
-
Wire & Cable Testers
UTP 03 60MHZ PROBE
Attenuation ratio: 1× and 10× optional.
Portable design according to ergonomics.
Integral injection moulding makes the usage more flexible and the oscillograph able to adapt more testing situations.
Safety standards: it has passed the CE Attestation of the European Community.
Compatible with domestic and international digital and analogue oscilloscopes in relevant frequency.
Measurement in intermediate and low-frequency signals.
Accessories included by PP series passive voltage rapier.
Adjusting tool: adjusts compensation capacitance to assure the rapier match with oscillograph.
Contractive-type acuminate hook.
12cm earth wire with an alligator clip.
Locating sleeve adapts to IC testing.
Double-nip wire.
SKU: n/a -
Wire & Cable Testers
UT18D Voltage and Continuity Tester
1. Auto power off, the conductor to be measured is greater than 12V
2. Phase rotation test3. Continuity test with buzzer and LED indication4. Low battery indication and over voltage prompt5. Flashlight6. Test live voltage without batteries7. Buzzer and silent modes available8. Auto range9. Polarity indicationSKU: n/a -
Wire & Cable Testers
MS6812 Cable Tracker
The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker
● Sound and Light Instruction
● Cont and Tone LED LightApplications
– Judge Continuity of the Cables or Wires
– Track the Cables or Wires, and Diagnose the Break Point
– Receive the Tone Signal on the Cables or Wires(Telephone Line)
– Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
– Send a Single Solid or a Dual Alternating Tone to the Target Cables or WiresSKU: n/a -
Wire & Cable Testers
UT681L Cable Tester
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
SKU: n/a
There are no reviews yet.