TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Out of stock
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
₨0
Out of stock
CompareTDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
Two cursors allow to determine the place of two damages simultaneously and the distance between them.
Thanks to the color 3,5” TFT display with a resolution of 320 x 240 pixels, the indication of the location of the damage is precise and the results easier to interpret.
Difficult environment conditions during measurement work are frequent problems encountered by electric installers and maintenance services. Thanks to the unique housing TDR-420 ensure a degree of protection on IP67 level, what means dustproof and protection against water penetration during short-term immersion. Therefore, working in very dusty terrain or accidental contact of the device with water will not affect the correct operation of the reflectometer.
Technical specification
- Measurement ranges: 7, 15, 30, 60, 120, 250, 500 m, 1, 2, 3, 6 km / 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 20000 ft
- Accuracy:1% of selected range
- Resolution: Approx. 1% of selected range
- Min. Cable length: 4 m / (14 ft)
- Velocity of propagation VoP: Adjustable from 10 to…99% or 15…148,5 m/µs
- Output Pulse: 5 Vp-p (open circuit)
- Output Impedance: 25, 50, 75, 100, 120, 200 Ω
- Output Impedance: 3 ns…3 µs (depends of range)
- Scan rate / mode: Up to 3 scans / second (CONT) or single (ONCE)
- Tone generator: 810 … 1110 Hz
- Battery Life: Up to 8 hours of continuous scan
- Power supply: 4 x alkaline batteries 1.5 V type AA or 4 x rechargeable batteries NiMH AA
- Auto-OFF: 1, 3, 5, 10, 15 minutes or deactivated
- Display: Color 3,5” LCD TFT, 320 x 240 pixels
- Voltage protection: 400 V DC / 250 V AC
- Dimensions: 220 x 98 x 58 mm (8.7 x 3.9 x 2.3 inches)
- Weight: 487 g
- Electromagnetic standard compatibility EMC: EN 61326-1
- Water/ Dust Proof: IP67
Nominal condition of use
- Operating temperature: -20..+70°C
- Storage temperature: -30…+80°C at humidity <80%
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-420 Time Domain Reflectometer/ Cable Fault Locator”
-
Earth Ground Resistance Testers
UT278A Clamp Earth Ground Testers
UT270 series is widely used in earth ground and circuit resistance measurements of electric power, telecommunications, meteorology, oil field, construction and industrial electrical equipment. It can measure the ground system of the circuit without disconnecting grounding wires, auxiliary electrode. UT278A can also measure leakage current and neutralline current of earth ground system
.
SKU: n/a -
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a -
Wire & Cable Testers
LKZ-1000 Wires and pipe locator
- Passive or active modes of tracing.
- Detection of underground live wires.
- Detection of underground wires with no voltage (radio mode).
- Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).
- Tracing metallic or non-conductive pipes using an additional probe.
- Tracing non-conductive pipelines using a “floating” probe.
- Tracing a determined cable.
- Determining the depth of a cable.
SKU: n/a -
Clamp Meters
UT202BT Smart AC Clamp Meter
1. Button-design clamp meter
2. One-hand operation and easy to use
3. True RMS / 9999 counts
4. Jaw opening: 28mm
5. Bluetooth 5.0
6. 600V DC voltage measurement
7. 600V AC voltage measurement
8. 600A AC current measurement
9. Inrush current measurement
10. Dual display: V+HZ and A+HZ
11. Temperature measurement
12. Low pass filter measurement
13. Bright backlight / Flashlight
14. Non-contact voltage (NCV)
15. CAT III 600VSKU: n/a -
Related products
-
Wire & Cable Testers
LKZ-1000 Wires and pipe locator
- Passive or active modes of tracing.
- Detection of underground live wires.
- Detection of underground wires with no voltage (radio mode).
- Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).
- Tracing metallic or non-conductive pipes using an additional probe.
- Tracing non-conductive pipelines using a “floating” probe.
- Tracing a determined cable.
- Determining the depth of a cable.
SKU: n/a -
Wire & Cable Testers
MS6812 Cable Tracker
The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker
● Sound and Light Instruction
● Cont and Tone LED LightApplications
– Judge Continuity of the Cables or Wires
– Track the Cables or Wires, and Diagnose the Break Point
– Receive the Tone Signal on the Cables or Wires(Telephone Line)
– Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
– Send a Single Solid or a Dual Alternating Tone to the Target Cables or WiresSKU: n/a
There are no reviews yet.