TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Out of stock
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
₨0
Out of stock
CompareTDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
Two cursors allow to determine the place of two damages simultaneously and the distance between them.
Thanks to the color 3,5” TFT display with a resolution of 320 x 240 pixels, the indication of the location of the damage is precise and the results easier to interpret.
Difficult environment conditions during measurement work are frequent problems encountered by electric installers and maintenance services. Thanks to the unique housing TDR-420 ensure a degree of protection on IP67 level, what means dustproof and protection against water penetration during short-term immersion. Therefore, working in very dusty terrain or accidental contact of the device with water will not affect the correct operation of the reflectometer.
Technical specification
- Measurement ranges: 7, 15, 30, 60, 120, 250, 500 m, 1, 2, 3, 6 km / 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 20000 ft
- Accuracy:1% of selected range
- Resolution: Approx. 1% of selected range
- Min. Cable length: 4 m / (14 ft)
- Velocity of propagation VoP: Adjustable from 10 to…99% or 15…148,5 m/µs
- Output Pulse: 5 Vp-p (open circuit)
- Output Impedance: 25, 50, 75, 100, 120, 200 Ω
- Output Impedance: 3 ns…3 µs (depends of range)
- Scan rate / mode: Up to 3 scans / second (CONT) or single (ONCE)
- Tone generator: 810 … 1110 Hz
- Battery Life: Up to 8 hours of continuous scan
- Power supply: 4 x alkaline batteries 1.5 V type AA or 4 x rechargeable batteries NiMH AA
- Auto-OFF: 1, 3, 5, 10, 15 minutes or deactivated
- Display: Color 3,5” LCD TFT, 320 x 240 pixels
- Voltage protection: 400 V DC / 250 V AC
- Dimensions: 220 x 98 x 58 mm (8.7 x 3.9 x 2.3 inches)
- Weight: 487 g
- Electromagnetic standard compatibility EMC: EN 61326-1
- Water/ Dust Proof: IP67
Nominal condition of use
- Operating temperature: -20..+70°C
- Storage temperature: -30…+80°C at humidity <80%
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-420 Time Domain Reflectometer/ Cable Fault Locator”
-
LCR Meter
MS8910 Smart SMD Tester (R/C)
The Tester is a handheld and battery operated very convenient small Tool that is specially used to measuring SMD (Surface Mounting Device), there are Chip type resistor, Chip type capacitor, and diode. Moreover, the Tester also has the continuity checking function.
● Display 3000 counts
● Auto Ranging
● Auto Power Off
● Data Hold
● Low Battery Display
● Auto Scanning
● Diode Check Open Voltage 2.8V
● Diode Testing Current 2mA
● Continuity Buzzer <30ΩSKU: n/a -
Digital Multi Meter
UT372D 2-in-1 Tachometer
UT372D 2-in-1 Tachometer is a reliable and safe tachometer, which combines contact and non-contact measurement modes. It is mainly used to measure Revolutions Per Minute(RPM) , frequency, surface velocity and length in the fields of motors, fans, automobiles, papermaking, etc.
SKU: n/a -
Function Generators
UTG9005C-II Function/Arbitrary Waveform Generato
1. Output waveforms: Sine, square, ramp, pulse, noise, DC, arbitrary
2. Output frequency range: Sine/square, 5MHz3. High-accuracy, broad-band 6 bit frequency counter, range: 100mHz~100MHz4. 4W power output5. EBTN LCD screenSKU: n/a -
Tools and Hardware
JM OP06 OPENING TOOL
DescriptionItem Description:- Features:
– Stainless steel material make it more durable.
– Anti-corrosion with stainless steel forged process.
– Easier to disassemble the electronic part accessories.
– Common used in laptops, mobiles and tablets disassembling.
– Special rolling-wheel design for better use in opening.
– The end of the tool with anti-slip design make it easier for disassembling.
– Precision processing technology on the metal part for better protection on the product itself. - Brand: JAKEMY
- Model: JM-OP06
- Material: Stainless steel
- Color: Orange & silver
- Package Weight: 45.0 G / 1.59 Ounces
- Package Dimensions (L*W*H): 180*80*13 MM / 7.09*3.15*0.51 Inches200
SKU: n/a - Features:
Related products
-
Wire & Cable Testers
UT681C Cable Tester
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
SKU: n/a -
Wire & Cable Testers
UT18D Voltage and Continuity Tester
1. Auto power off, the conductor to be measured is greater than 12V
2. Phase rotation test3. Continuity test with buzzer and LED indication4. Low battery indication and over voltage prompt5. Flashlight6. Test live voltage without batteries7. Buzzer and silent modes available8. Auto range9. Polarity indicationSKU: n/a -
Wire & Cable Testers
LKZ-720 Wires and pipe locator
Features:
- the function 3D in the receiver – detecting the direction of current flow and accurate locating the object,
- phase detection mode,
- receiver operation with four transmitters at the same time to locate interruptions or distinguish wires,
- a LED bright torch,
- headphone socket in receiver,
- screens backlight for work in dark,
- transmission battery status and settings of the transmitter to the receiver
- operation in wide range of rated voltage, up to 500V RMS,
- measurement of voltage at the object to 500 Vrms,
- three levels of transmitter amplification,
- automatic or manual selection of transmitter operation modes,
- five modes of wire tracer operation – voltage, current, current-voltage, power and clamp,
- software upgrade via USB,
- additional accessories enable precise localization – such as contact or non-contact probes and measurement clamp.
SKU: n/a
There are no reviews yet.