TND 500VA Subtotal: ₨7,896
-2%
Digital Multi Meter
UT60BT
Features of UT60 Series Digital Multimeters
Certificates: CE, UKCA, cETLus
● 9999 counts
● True RMS
● Bluetooth
● Duty cycle
● Diode/Continuity test
● Temperature
● Non-contact voltage
● Analog bar/Data hold
● Backlight/Relative mode
● Auto/Manual range
● Low battery indication
● Three-color LED light indicator
Video for UT60EU:
Video for UT60S:
₨7,680 ₨7,848
UT60 Series Digital Multimeters
UT60 series digital multimeters provide True-RMS measurement, 9999-count resolution, non-contact voltage detection and many convenient features for users’ testing needs. These auto-ranged meters can measure up to 1000V AC/DC voltage, 10A AC/DC current and 100MΩ resistance. The easy-to-use interface with backlight enables you to detect equipment quickly even in dark places. This CE certified meter meets CAT II 1000V/CAT III 600V safety rating with rugged double-injection housing.
Models in the UT60 Series: UT60EU, UT60BT, UT60S
Brand
UNI T
Based on 0 reviews
Be the first to review “UT60BT”
-
Oscilloscopes
UTD2072CEX-II Digital Storage Oscilloscope
1. 2 channels
2. 70MHz/100MHz bandwidth; 1GSa/s real-time sampling rate3. Up to 28Mpts memory depth4. Calibration signal output: 10Hz, 100Hz, 1kHz (by default),10kHz or 100kHz5. Max 10Mpts waveform record6. 8-inch TFT LCD, WVGA (800X480)SKU: n/a -
Multimeters
UT107 Handheld Automotive Multi-Purpose Meters
Main Features
1. Dwell angle measurement (DWELL)
2. Tach measurement (RPM)
3. Data hold
4.12V battery test, duty ratio measurement
5. Measurement input port prompt
6. Low battery, auto polarity and over-range indication
7. Complies with CE (European Union) directives
SKU: n/a -
Multimeters
UT125C Pocket Size Digital Multimeter
1. Small size, easy to carry and operate
2. 600V DC/AC voltage measurement3. 400mA DC/AC current measurement4. Resistance/Capacitance/Diode/Continuity test5. Frequency/Duty cycle measurement6. CE (EMC, LVD, RoHS), cETLus7. CAT III 600V8. 1m drop testSKU: n/a -
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
-
Wire & Cable Testers
UT681C Cable Tester
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
SKU: n/a
There are no reviews yet.