-
×
UT139C True RMS Digital Multimeters
- Vendor:
superworld
Subtotal: ₨12,000
-12%
Wire & Cable Testers
UT681C Cable Tester
Availability:
20 in stock
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
₨3,074 ₨3,509
20 in stock
CompareMain Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
| Weight | 0.2 kg |
|---|---|
| Dimensions | 10 × 6 × 3 cm |
| tem | Function | Model | Description |
| UT681C | |||
| Test function | To test for: RJ45/RJ11/BNC | √ | Need to use RJ45 to BNC adaptor |
| Fast test mode | √ | LED1~LED8, LED_G | |
| Low test mode | √ | LED1~LED8, LED_G | |
| To test for the case of short circuit, crossover, open circuit, etc. | √ | ||
| Ethernet cable: shielded/unshielded test | √ | ||
| Manual shutdown function | √ | ||
| Auto shutdown function | √ | No operation within 10 minutes, the device will shut down automatically | |
| Single key operation | √ | ||
| Power supply: 9V battery | √ | ||
| Low voltage detection | √ | About less than 7.2V | |
| Application environment | Working temperature: 0~40℃ | √ | |
| Storage temperature: -10~50℃ | √ | ||
| Working humidity: 20~80% RH | √ | ||
| Storage humidity: 10~90% RH | √ | ||
| Altitude: ≤2000 meters | √ | ||
| Safety
standard |
CE EN61326-1: 2013;
EN61326-2-2: 2013 |
√ |
Brand
UNI T
Based on 0 reviews
Be the first to review “UT681C Cable Tester”
-
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a -
Earth Ground Resistance Testers
UT278A Clamp Earth Ground Testers
UT270 series is widely used in earth ground and circuit resistance measurements of electric power, telecommunications, meteorology, oil field, construction and industrial electrical equipment. It can measure the ground system of the circuit without disconnecting grounding wires, auxiliary electrode. UT278A can also measure leakage current and neutralline current of earth ground system
.
SKU: n/a
Related products
-
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
-
Wire & Cable Testers
TDR-410 Cable Fault Locator
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
SKU: n/a -
-
Wire & Cable Testers
MS6812 Cable Tracker
The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker
● Sound and Light Instruction
● Cont and Tone LED LightApplications
– Judge Continuity of the Cables or Wires
– Track the Cables or Wires, and Diagnose the Break Point
– Receive the Tone Signal on the Cables or Wires(Telephone Line)
– Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
– Send a Single Solid or a Dual Alternating Tone to the Target Cables or WiresSKU: n/a -
Wire & Cable Testers
UTP 03 60MHZ PROBE
Attenuation ratio: 1× and 10× optional.
Portable design according to ergonomics.
Integral injection moulding makes the usage more flexible and the oscillograph able to adapt more testing situations.
Safety standards: it has passed the CE Attestation of the European Community.
Compatible with domestic and international digital and analogue oscilloscopes in relevant frequency.
Measurement in intermediate and low-frequency signals.
Accessories included by PP series passive voltage rapier.
Adjusting tool: adjusts compensation capacitance to assure the rapier match with oscillograph.
Contractive-type acuminate hook.
12cm earth wire with an alligator clip.
Locating sleeve adapts to IC testing.
Double-nip wire.
SKU: n/a
There are no reviews yet.