Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Insulation Tester
Insulation Resistance Testers UT511
UT510 series is a kind of intelligent insulation tester. The device circuit design takes microcomputer technology design as the core and combines the large scale integrated circuit with digit circuit. It is equipped with strong measuring software and data processing software. It is applied to the parameter measurement of insulation resistance, voltage and low resistance. It has stable performance and simple operation. It is applicable to on-site measurement and repair of the electrical equipment and charging line. It is the ideal tool of maintaining electrical equipment. It is also used for smelting, communication, manufacture, fossil oil, national defense, electricity, chemical industry and circuit.
SKU: n/a -
IR Resolution
UNI-T UTi320E High IR Resolution 320×240 Professional Handheld Thermal Imager with PC,WiFi and App Connect Support Data Analysis and Real Time Display
IR ResolutionUNI-T UTi320E High IR Resolution 320×240 Professional Handheld Thermal Imager with PC,WiFi and App Connect Support Data Analysis and Real Time Display
Screen Display 3.5″IPS Temeperature Range -40°~400° IR Resolution(Pixels) 320×240 Visible Camera Resolution 2MP Field of View(FOV) 56°x 42° Spatial Resolution(IFOV) 3mrad Frame Rate 9Hz Thermal Sensitivity(NETD) 65mK Measurement Accuracy ±2° or ±2%
whichever is greaterEmissivity 0.01-0.99 Adjustable Spectral Range 8~14μm Foucs Foucs Free Digital Zoom 2x, 4x Palattes 7(Iron, Rainbow, White Hot, Red Hot, Black Hot, Lava, Rainbow HC) Display Modes Thermal,Visible,Fusion,PIP Mesurement Mode Center Pot,High/Low Temp Pot,ROI Temperature Analysis (Point 5 /Line 1 /Area 6 ) total 6 tools Battery Li-ion battery pack 5200mAh Battery Type Replaceable Battery Life ≥ 4hours Charging Time ≤5Hours Communication interface Type-C IP Rating IP54 Drop Proof 2m Functions Flashlight √ Tripod Hole √ Auto tracking of High/Low Temperature √ Auto Alarm of High/Low Temperature √ Image Capture √ Video Recording × Voice Recording × RIO(Eliminates Interference) √ Isotherm √ PC Real Time Image Transmisstion √ PC Analysis Software √ Wifi Photo Download √ Wifi Real Time Display × Bluetooth × Mobile APP √ GPS × Laser/Distance Measurement × SKU: n/a -
Tool Kits, Tools and Hardware
JM – 8105 27 in 1 Screwdriver Kit
Main Features:
● It includes 20 screw head types: Slotted (1.5mm / 2.0mm / 2.5mm / 3.0mm); Cross (1.0mm / 1.5mm / 2.0mm / 2.5mm); Torx (T3 / T4 / T5 / T6 / T7 / T8 / T10 / T15 / T20 / 0.8mm); Hex (H1.3 / H1.5 / H3.0 / H4.0); U2.6; Y2.0; Triangle:2.0
● It also includes one plastic handle
● Great tool for cell phone and computer repairSKU: n/a -
Oscilloscopes
UPO2104CS 4 Channels Ultra Phosphor Oscilloscope
Features and Benefits:
1、Sample Rate up to 1GS/s；
2、Channels 4；
3、Bandwidth 100MHz，；
4、Memory Depth 28Mpts (Standard)；
5、Waveform Capture Rate up to 50,000wfms/s；
6、With 256 level intensity grading display；
7、Up to 65,000 frames for Waveform Record ,Replay；
8、Support serial bus trigger and decoding；
9、8 inches, TFT LCD，WVGA(800*480)；
10、Interface：USB Host, USB Device, LAN, VGA, AUX OUT, 10MHz input/output.SKU: UP21O02CSMHZ
Related products
-
Battery Testers
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
SKU: n/a -
-
Battery Testers
UT675A Battery Testers
Features of UT675A Battery Testers
Certifications: CE, UKCA, FCC
● 12V cranking lead acid battery test
● 12/24V charging or cranking system test● Display battery capacity, voltage, resistance and life● Four-termina Kelvin test● 10 types of battery standards● Language option (Chinese/English)● Test without battery disassembly● LED color indication for test result (UT673A)● Print on-line and real-time test reports (UT675A)● USB data transfer (UT675A)SKU: n/a -
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a
There are no reviews yet.