CMP-2000 Digital clamp-on multimeter
5 in stock
It provides:
- AC current measurement (TRUE RMS) up to 1500 A and DC up to 2000 A.
- Measurement of INRUSH current in start-up phase of electrical device.
- AC voltage measurement (TRUE RMS) up to 750 V and DC up to 1000 V.
- Resistance measurement and continuity test:
– continuity test with acoustic signalling (beeper) for resistance below 30 Ω. - Capacitance measurement.
- Temperature measurement (Fahrenheit or Celsius).
- Frequency measurement.
- Duty cycle measurement.
- Diode test.
₨61,859 ₨65,809
5 in stock
Compare-
Universal clamp meter, enabling the maintenance of current measurements up to 2000 A, with the diameter of the clamp as 57 mm, and bus bar to 70 * 18 mm
The instrument has an electronic overload protection of all functions and ranges.
| Weight | 0.6 kg |
|---|---|
| Dimensions | 28 × 11 × 5 cm |
AC current measurement (TRUE RMS) up to 1500 A and DC up to 2000 A.
Measurement of INRUSH current in start-up phase of electrical device.
AC voltage measurement (TRUE RMS) up to 750 V and DC up to 1000 V.
Resistance measurement and continuity test:
- continuity test with acoustic signalling (beeper) for resistance below 30 Ω.
Capacitance measurement
Temperature measurement (Fahrenheit or Celsius).
Frequency measurement.
Duty cycle measurement.
Diode test.
Additionally:
- safe, insulated measuring clamp,
- autoranging,
- „DATA HOLD” function, for holding measured values,
- backlit LCD,
- „DC ZERO” mode of measurement for DC current, possibility to zero the display and reading relative actual value less stored „zero” value,
- „MAX/MIN” function,
- over range indication,
- „AUTO-OFF” function after 30 min.
Electric security:
- measurement category: CAT IV 600 V acc. to EN 61010 – 1,
- protection class acc. to EN 60529: IP20,
Other technical data:
- power supply, 9 V battery type 6LR61,
- display: 6600 counts, backlit LCD,
- continuity test: threshold 30 Ω,
- diode test: test current of 0,8 mA , typical open circuit voltage 3,2 V DC, typical,
- low battery indication: BAT displayed,
- over range indication: ‘OL’ displayed,
- temperature sensor: type K thermocouple,
- input impedance: ca.10 MΩ (V DC and V AC),
- AC bandwidth: 50…500 Hz,
- auto power OFF: 30 minutes,
- dimensions: 281 x 108 x 53 mm,
- weight: 570 g (with battery),
- accordance with following standards: EN 61010 – 1, EN 61010 – 2-032.
Rated operational conditions:
- able to open the clamp: Ø 57 mm wire 70 x 18 mm bus bar,
- operating temperature: 0…+50 °C,
- storage temperature: -20…+60 °C,
- operating altitude: max 2000 m.
DC current measurement
| Range | Resolution | Accuracy |
| 0,0…659,9 A | 0,1 A | ±(2,0% m.v. + 5 digits) |
| 660…2000 A | 1 A | ±(3,0% m.v. + 5 digits) for 660…1000 A |
| ±(5,0% m.v. + 5 digits) for 1000…2000 A |
AC current measurement (TRUE RMS)
| Range | Resolution | Accuracy |
| 0,0…659,9 A | 0,1 A | ±(2,0% m.v. + 10 digits) for 50…60 Hz |
| ±(3,0% m.v. + 10 digits) for 61…400 Hz | ||
| 660…1500 A | 1 A | ±(2,5% m.v. + 10 digits) for 50…60 Hz i 660…1000 A |
| ±(3,5% m.v. + 10 digits) for 61…400 Hz and 660…1000 A |
||
| ±(5,0% m.v. + 10 digits) for 50…400 Hz and 1000…1500 |
DC voltage measurement
| Range | Resolution | Accuracy |
| 0,000…6,599 V | 0,001 V | ±(0,5% m.v. + 2 digits) |
| 6,60…65,99 V | 0,01 V | |
| 66,0…659,9 V | 0,1 V | |
| 660…1000 V | 1 V |
AC voltage measurement (true RMS)
| Range | Resolution | Accuracy |
| 0,000…6,599 V | 0,001 V | ±(1,5% m.v. + 8 digits) for 50…500 Hz |
| 6,60…65,99 V | 0,01 V | |
| 66,0…659,9 V | 0,1 V | |
| 660…750 V | 1 |
Resistance measurement
| Range | Resolution | Accuracy |
| 0,0…659,9 Ω | 0,1 Ω | ±(1,0% m.v. + 5 digits) |
| 0,660…6,599 kΩ | 0,001 kΩ | |
| 6,60…65,99 kΩ | 0,01 kΩ | |
| 66,0…659,9 kΩ | 0,1 kΩ | |
| 0,660…6,599 MΩ | 0,001 MΩ | ±(2,0% m.v. + 5 digits) |
| 6,60…66,00 MΩ | 0,01 MΩ | ±(3,5% m.v. + 5 digits) |
Capacitance measurement
| Range | Resolution | Accuracy |
| 0,0…6,599 nF | 0,001 nF | ±(3,0% m.v. + 30 digits) |
| 6,60…65,99 nF | 0,01 nF | ±(3,0% m.v. + 10 digits) |
| 66,0…559,9 nF | 0,1 nF | ±(3,0% m.v. + 30 digits) |
| 6,600…59,999 µF | 0,001 µF | ±(3,0% m.v. + 10 digits) |
| 66,00…659,99 µF | 0,01 µF | |
| 660…659,999 µF | 0,100 µF | |
| 0,660…6,600 mF | 0,001 mF |
Frequency measurement
| Range | Resolution | Accuracy |
| 10…65,99 Hz | 0,01 Hz | ±(0,1% m.v. + 5 digits) |
| 66,0…659,9 Hz | 0,1 Hz | |
| 0,660…6,599 kHz | 0,001 kHz | |
| 6,60…65,99 kHz | 0,01 kHz | |
| 66,0…659,9 kHz | 0,1 kHz | |
| 0,660…1,000 MHz | 0,001 MHz |
Temperature measurement
| Range | Resolution | Accuracy |
| -20…0°C | 1°C | ±(2,0% m.v. + 3°C) |
| 0…399°C | ±(1,0% m.v. + 2°C) | |
| 400…1000°C | ±(2,0% m.v. + 3°C) | |
| -4…31°F | 1°F | ±(2,0% m.v. + 6°F) |
| 32..749°F | ±(1,0% m.v. + 4°F) | |
| 750…1832°F | ±(2,0% m.v. + 6°F) |
Duty cycle measurement
| ange | Resolution | Accuracy |
| 5…95% | 0,1% | ±(2,0% m.v. + 10 digits) |
„m.v.”- measured value
Brand
SONEL
Based on 0 reviews
Be the first to review “CMP-2000 Digital clamp-on multimeter”
-
-
LCR Meter
UT620 Series Digital Micro Ohm Meters
UT620 series are used to measure DC low resistance through 4-wire method. Some of its features are: Comparison function to determine if the device is in good condition, unknown wire length calculation (FT/M); two-way data transmission by USB interface; built-in rechargeable lithium battery. UT620 can be used in narrow space for on-site troubleshooting, such as metal coating resistance/motor and small transformer winding resistance measurement, earth system joints/welding points/power distribution cabinet bus and lead connection inspection and more.
SKU: UN62B0TUOM -
DC Power Supplies
YIHUA 605D DC Power Supply
YH-605D communication maintenance power supply
605D communication maintenance power supply is a single line output of stabilized high accuracy
DC stabilized power supply. The output voltage and current can be adjusted continuously within
the rated range. Double digital display shows output voltage and current independently. Several
protection functions include current limitation, voltage reduction, short circuit protection, over-
temperature protection, etc.
The design is applied to production line of the plant, maintenance, laboratories and is also
a necessary device for the communication industry.
SKU: n/a -
Tool Kits, Tools and Hardware
JM-8101 Precision Screwdriver Tool Kit
Features:
- Adjustable screwdriver bits for different screws.
- Finest CR-V bits with HRC up to 52 ℃.
- Common used in precision work in electronics, DIY models, jewelry, eye glasses and other home appliances.
- Curved tip tweezer common used in mini electronic components.
- Portable box with transparent cover.
SKU: n/a
Related products
-
Clamp Meters
UT-CS09A Flex Clamp Sensor
Specifications Range UT-CS09A AC current (A) 30A/300A/3000A ±(3%+5) Frequency response (Hz) 45Hz~500Hz √ Features Flex clamp size UT-CS09A: 25.4cm (10 inches); UT-CS09C: 45.7cm (18 inches) Operating temperature 0℃~50℃ Storage temperature -20°C~60°C Storage humidity ≤80%RH Low battery indication About 3.3V Range selection Manual General Characterisitics Power 1.5V battery (R03) x 3 Product color Red and grey Product net weight 260g Product size 267mm x 119.4mm x 34mm Standard accessories Batteries, BNC adapter Standard individual packing Blister, English manual Standard quantity per carton 10pcs Standard carton measurement 495mm x 405mm x 225mm Standard carton gross weight 7kg SKU: n/a -
Clamp Meters
UT281C True RMS AC 3000A Flexible Clamp Meters
1. 2m drop proof, IP54, ETL/Intertek certified 3rdedition CE
2. Coil diameter: 0.75cm, bending length: 24.5cm for UT281A and 45.7cm for UT281C
3. Large LCD display for clear reading
4. True RMS
5. Long press INRUSH key for 2s to measure inrush current
6. Datahold, backlight, auto power off
SKU: n/a -
Clamp Meters
UT219DS ACA DCA Professional Clamp Meters with Motor LPF Test
- UT-219 professional clamp meter series is three-proofing digital clamp meter specially designed for professional industrial users.
- The industrial design of this series is rugged and durable, and capable of withstanding the impact from 2 meters fall-down.
- The waterproof rating is up to IP54; therefore, it can be used in environment with water splashing or much more dust.
- The whole series is configured with LoZ (Low Impedance Input) AC voltage tap position, which is capable of testing the false voltage; auto backlight function can be used continuously under the circumstance of emergency power outage.
- UT-219DS is also provided with MOTOR test function, allowing to directly test the phase sequence of three phase AC motor by means of the probe. UT-219 series is much more in compliance with CAT IV 600V safety level, and certified by the German GS institution.
SKU: n/a -
Clamp Meters
MT87 3 1/2 Digits LCD Digital Clamp Meter
This meter features a portable design, 31/2 LCD display and 25mm jaw opening, which can provides various measurements for AC/DC voltage, AC current, resistance, diode and continuity buzzer. It is also with functions of date hold, low battery indication, overload indication, etc. More detailed product information, please refer to the English manual.
SKU: MT 87 CLAMP METER
There are no reviews yet.