1. Ergonomic exterior, comfortable handling
Laser Distance Meters
LM100D Laser Distance Meter (Curvature Edition)
Availability:
9 in stock
1. Ergonomic exterior, comfortable handling
2. Millimeter accuracy
3. Large, HD display
4. Auto voice and audio indication
5. Curvature measurement, test curve length via the roller
6. Auto power off after 3 minutes without operation
7. Convenient angle measurement via electronic leveling
₨18,000 ₨28,613
9 in stock
Compare2. Millimeter accuracy
3. Large, HD display
4. Auto voice and audio indication
5. Curvature measurement, test curve length via the roller
6. Auto power off after 3 minutes without operation
7. Convenient angle measurement via electronic leveling
Weight | 0.4 kg |
---|---|
Dimensions | 10 × 6 × 4 cm |
Specifications | LM100D |
Display type | EBTN |
Display size | 2.4 inches |
Range | 100m |
Min. display unit | 0.001m |
Measurement units | m/ft/in |
Measurement basis | Front/middle/rear |
Accuracy | ±(2mm+5 x 10-5 D) |
Laser class | 2 |
Laser type | 630~670nm, ﹤1mW |
Features | |
Single measurement | √ |
Continuous measurement | √ |
Max/Min/Area | √ |
Volume | √ |
Pythagoras | √ |
Triangle area | √ |
Auto leveling horizontal | √ |
Auto leveling vertical | √ |
Add/Subtract | √ |
Curvature measurement | √ |
Displacement | √ |
Trapezoid | √ |
Data storage | 20 groups |
Auto power off | 3 minutes without operation |
Auto laser off | 30s without operation |
Auto backlight off | 10s without operation |
Electronic leveler | √ |
Audio/Voice indication | √ |
Battery status display | √ |
Line laser marking | √ |
Storage temperature | -20℃~70℃ |
Operating temperature | 0℃~40℃ |
Based on 0 reviews
Be the first to review “LM100D Laser Distance Meter (Curvature Edition)”
-
Insulation Resistence Tester
UT516B Insulation Resistance Tester
Features of UT516B Insulation Resistance Tester
● AC/DC voltage
● USB data transfer● Low battery indication● Data storage● LCD backlight● Polarization Index● Over-range alarm● 9999 Max display● Comparative measurement● Measurement time selectionSKU: n/a -
Multimeters
CMM-40 Industrial Multimeter
The most important features of CMM-40 are:
- autoranging/manual range selection,
- „DATA HOLD” function, for holding measured values,
- „REL” function, which allows you to make measurements relative to a stored reference value,
- „MAX/MIN” function,
- „PEAK HOLD” function,
- memory for 2000 measurement resultS,
- continuity test with acoustic signalling (beeper),
- „AUTO-OFF” function,
- display 4¾ digits (40000 max),
- double molded, waterproof casing.
SKU: n/a -
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
-
Analog Multimeters
ANALOG METER YX 360TR BS
Features Of Handheld YX-360TRE-B Analog Meter Voltmeter:
- High accuracy analogue multimeter for general purposes.
- Mirrored needle indicator with an accurate reading.
- Check both AC and DC parameters with continuity buzzer on Ohms.
- Up to 1000V on both AC and DC Voltage.
- 19 versatile ranges for general-purpose testing.
- Fuse & Diode protection.
- Compact sizing.
- Tilt back-stand.
- The large and mirrored scale of 80mm length.
SKU: n/a
There are no reviews yet.