UT681C Cable Tester
20 in stock
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
₨3,074 ₨3,509
20 in stock
CompareMain Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
| Weight | 0.2 kg |
|---|---|
| Dimensions | 10 × 6 × 3 cm |
| tem | Function | Model | Description |
| UT681C | |||
| Test function | To test for: RJ45/RJ11/BNC | √ | Need to use RJ45 to BNC adaptor |
| Fast test mode | √ | LED1~LED8, LED_G | |
| Low test mode | √ | LED1~LED8, LED_G | |
| To test for the case of short circuit, crossover, open circuit, etc. | √ | ||
| Ethernet cable: shielded/unshielded test | √ | ||
| Manual shutdown function | √ | ||
| Auto shutdown function | √ | No operation within 10 minutes, the device will shut down automatically | |
| Single key operation | √ | ||
| Power supply: 9V battery | √ | ||
| Low voltage detection | √ | About less than 7.2V | |
| Application environment | Working temperature: 0~40℃ | √ | |
| Storage temperature: -10~50℃ | √ | ||
| Working humidity: 20~80% RH | √ | ||
| Storage humidity: 10~90% RH | √ | ||
| Altitude: ≤2000 meters | √ | ||
| Safety
standard |
CE EN61326-1: 2013;
EN61326-2-2: 2013 |
√ |
Brand
UNI T
Based on 0 reviews
Be the first to review “UT681C Cable Tester”
-
Earth Ground Resistance Testers
MRU-10 Earth Resistance Meter
It allows to:
- measure earthing resistance using auxiliary electrodes,
- measurement of resistance of auxiliary electrodes RS and RH,
- measurement of interference voltage,
- measurement in the presence of interference voltage in the power network with frequency 50 Hz and 60 Hz,
- selection of maximum measuring voltage (25 V and 50 V),
- indication of battery state.
SKU: n/a -
Spudger
JM OP07 METAL SPUDGER SET
DescriptionItem Description:- Material: Metal
- Brand: JAKEMY
- Features:
– Dual tipped design, various blades for every repair situation.
– Easy to use and handle.
– 3-in-1 metal set.
– Made of stainless steel, sturdy yet still flexible. - Brand:JAKEMY
- Model: JM-OP07
- Material: Stainless steel
- Place of Application: Repair
- Note:
Be careful when using these tools.With their great strength comes the potential to scratch or otherwise damage components that might be better served with plastic tools such as a plastic tool.
SKU: n/a
Related products
-
Wire & Cable Testers
UT18D Voltage and Continuity Tester
1. Auto power off, the conductor to be measured is greater than 12V
2. Phase rotation test3. Continuity test with buzzer and LED indication4. Low battery indication and over voltage prompt5. Flashlight6. Test live voltage without batteries7. Buzzer and silent modes available8. Auto range9. Polarity indicationSKU: n/a -
Wire & Cable Testers
UTP 04 100MHZ PROBE
Features Of UNI-T Best Passive Probe 100MHz UTP04:
This passive probe is good oscilloscope accessories, it is suitable for oscilloscope.
Stable performance and not easy to break.
This can provide a professional and accurate measurement.
Widely used, it can satisfy most peoples.
A good helper for instrument engineer.
SKU: n/a -
Wire & Cable Testers
TDR-410 Cable Fault Locator
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
SKU: n/a -
There are no reviews yet.