1. Dual analog channels width range 1mV/div~20V/div;
2. 7 inches widescreen LCD displays;
3. Special Print Scree Feature;
4. Supports plug-and-play USB storage device. Communication with and remote control of computer through the USB device;
5. USB drive system software upgrade;
6. Storage of waveforms setups and interfaces waveforms and setups reproduction;
7. Automatic measurement of 28 waveform parameters;
8. Unique waveform recording and replay function;
9. Multilingual menu displays.
UTD2025CL Digital Storage Oscilloscope
10 in stock
1. Dual analog channels width range 1mV/div~20V/div;
2. 7 inches widescreen LCD displays;
3. Special Print Scree Feature;
4. Supports plug-and-play USB storage device. Communication with and remote control of computer through the USB device;
5. USB drive system software upgrade;
6. Storage of waveforms setups and interfaces waveforms and setups reproduction;
7. Automatic measurement of 28 waveform parameters;
8. Unique waveform recording and replay function;
9. Multilingual menu displays.
₨72,000 ₨78,000
10 in stock
CompareWeight | 2.2 kg |
---|---|
Dimensions | 31 × 15 × 12 cm |
Specification | UTD2025CL |
Channels | 2 |
Bandwidth | 25MHz |
Sample Rate | 250MS/s |
Rise Time | ≤14ns |
Memory Depth | 25kpts |
Waveform Acquisition Rate | ≥2000wfms/s |
Vertical Sensitivity | 1mV/div~20V/div |
Timebase Range | 10ns/div~50s/div |
Storage | Setup,Wave,Bitmap |
Trigger Modes | Edge, Pluse, Video, Alternate |
Interface | USB OTG,Pass/Fail |
General Characteristic | |
Power | 100-240VAC, 40-440Hz |
Display | 7 Inches 64K Color TFT LCD, 400×240 |
Product Color | White and Gray |
Product Net Weight | 2.2 kg |
Product Size (W×H×D) | 306mm ×147mm × 122mm |
Standard Accessories | Probe×2 (1×,10× switchable),Power Cord, USB Cable, PC Software CD |
Standard Individual Packing | Gift Box, English Manual |
Standard Quantity Per Carton | 2 PCs |
Standard Carton Measurement (L×W×H) | 450mm × 420mm × 280mm |
Standard Carton Cross Weight | 8.5 kg |
Based on 0 reviews
Be the first to review “UTD2025CL Digital Storage Oscilloscope”
-
Multimeters
CMM-40 Industrial Multimeter
The most important features of CMM-40 are:
- autoranging/manual range selection,
- „DATA HOLD” function, for holding measured values,
- „REL” function, which allows you to make measurements relative to a stored reference value,
- „MAX/MIN” function,
- „PEAK HOLD” function,
- memory for 2000 measurement resultS,
- continuity test with acoustic signalling (beeper),
- „AUTO-OFF” function,
- display 4¾ digits (40000 max),
- double molded, waterproof casing.
SKU: n/a -
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
There are no reviews yet.