The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Multimeters
UT139C True RMS Digital Multimeters
UT139 Series digital multimeters are newly designed to offer users better performance and higher safety rating. Totally over-load protection and unique structural design make it new type of multimeter with high performance/ price ratio and a best choice for electricians used in electrical maintenance and repairing.
1、True RMS for the whole series;
2、Measure signals with varied frequency (VFC);
3、Measure large capacitance up to 100mF;
4、Optional AC/DC 60A current clamps in different models to measure current up to 60A(1mv=1A);
5、NCV designed for the whole series, a necessity for electricians;
6、AA1.5V*2(5#) battery, easy for users to purchase and replace;
7、Soft rubber holster is easy to stand 2m drop;
8、Optional magnetic hanging strap offered to facilitate tests in special location;
9、Fast to replace fuse, just by opening battery cover;
10、Reliable with use of internal 2PCS fuses with high-breaking capacity;
11、Protection against 600V input/1 minute from misconnection;
12、Safety Rating: CAT III 600V.Applications
An ideal tool for equipment testing, maintenance and repair widely needed in electronics, electric power, schools, metallurgy, communications, manufacturing, petroleum, national defense, chemical industry, etc.SKU: n/a -
Multimeters
UT18B Voltage And Continuity Testers
UT18 series of test pen with measuring AC and DC voltage (including the three-phase alternating current) measurement, phase of three-phase AC power indicator, on-off test, RCD test, single pen measurement (can determine the zero line or wire), self checking, no battery detection and other functions.
Suitable for: smelting, electronics, manufacturing, defense, electric power, petroleum, chemical industry. Also used to solve complex problems of electronic, factory automation, power distribution and electrical equipment in.SKU: n/a -
Clamp Meters
CLAMP METER AC MT 87
- ) AC voltage: 450V ( ?1.2% )
- 3) OHM: 200K? (?1.0%)
- 4) ACA: 20-400A (?2.0%)
- 5) Power supply: (AAA) 1.5V?2
- 6) Data hold: YES
- 7) Dimension 150L?63W?27.5Hmm
- 1) 3 1/2 digits LCD with a Max. Reading of 1999
- 2) Diode and Buzzer function
- 3) Low battery indication
- 4) Overload protection
- 5) Data hold for easy reading
- 1) DC voltage: 600V (?1.0%)
- 2) AC voltage: 450V ( ?1.2% )
- 3) OHM: 200K? (?1.0%)
- 4) ACA: 20-400A (?2.0%)
- 5) Power supply: (AAA) 1.5V?2
- 6) Data hold: YES
- 7) Dimension 150L?63W?27.5Hmm2
SKU: n/a -
Digital Multi Meter
UNI-T UTi320V Thermal Image
Technical Specifications of UTi320V Thermal Image:
Specifications Model UTi320V Temperature range -20~350℃ -4℉~662℉ Temperature accuracy ±2℃ or ±2% (whichever is greater) Temperature resolution 0.1℃/0.18℉ Thermal resolution 320×240 Temperature coefficient ± 0.1/℃ or ± 0.1%/℃ (whichever is greater) Visible light resolution 640×480 Emissivity Adjustable (0.01-1.00), 0.98 in default Reflectivity Reflectivity correction (adjustable background temperature) Palettes White hot, iron red, arctic, rainbow 2, hot iron, rainbow 1 High/low temperature tracking √ High/low temperature alarm √ Image blending/Picture in picture √ WIFI mode Connects to PC software and moblie phone App Lens 7mm Focus Focus free FOV 42.5°×32.5° NETD ≤60mK Image frequency 50Hz Digital zoom ×2, ×4 General Characteristics Power 7.4V 2300mAh Li-ion battery Display 3.5-inches TFT LCD Product color Red and grey Product net weight 1.8kg (Package) Product size 258mm x 98mm x 90mm Standard accessories Li-on battery x 2, USB power supply with multi plugs,
wrist strap, adaptor×5, SD card, USB cable, PC software CDStandard individual packing Gift box, tool box, English manual Standard quantity per carton 1pcs Standard carton measurement 410mm x 265mm x 180mm Standard carton gross weight 2.2kg SKU: n/a
There are no reviews yet.