The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Soldering Iron
YH 929D V ELECTRIC VACUUM DESOLDERING IRON
About this item
- This 929D-V desoldering iron integrates soldering iron and desoldering pump, you can enjoy the single-handed and continuous desoldering with its short charging handle to rid the hassle of changing grip positions. If you are looking to purchase a desoldering tool that can handle the desoldering jobs of through-hole components and removing excess solder (solder bridges) without jamming up, this is a great choice.
- This is a plug-n-play desoldering iron. Plug in the power plug, allow the desoldering iron to preheat for approximately 3 minutes, and you are ready to go. YIHUA exclusive heating system combined with a strong desoldering pump ensures you experience uninterrupted desoldering.
- Different from the traditional use-and-throw desoldering irons, the 929D-V can be used, easily cleaned, and reused. You can lift and pull out the scrap solder storage tube and clean the solder out like a breeze. Meanwhile, we also included 2 different and interchangeable diameters (φ1.0mm & φ1.2mm) desoldering nozzles for different sizes of through-hole components. NOTE: change the nozzle after the desoldering iron has cooled completely.
- This desoldering iron comes with a heat deflector at the end of the heating element, and this prevents the excess heat from transferring onto the hand when desoldering continuously. You can desolder joints after joints without your hands feeling uncomfortably hot.
- Choose YIHUA with Confidence – Our US-exclusive 12-month manufacturer warranty will apply to your purchase. Plus, our team is providing professional assistance 24/7 on Amazon. NOTE: This model only works on 110-127V with its USA plug. This product contains electrical insulator protective material (mica), it is normal for the product to emit white fumes for no longer than 20 minutes on first use. This is a normal and intended occurrence for this product, please rest assure for safe usage.
SKU: n/a -
Multimeters
UT533 Insulation Multimeter
Features of UT533 Insulation Multimeter
Certifications: CE, RoHS
● AC/DC voltage measurement
● AC/DC current measurement● Insulation resistance measurement● Resistance & Capacity test● Frequency & Temperature test
● 1000V output voltage● Double insulation designSKU: n/a -
Bags and Box, Tools and Hardware
JM-B02 Professional Orange & Black Tool Bag
High-end tool bag (big size) JM-B02
Assembly and repairing of household appliances, elevator and other large mechanical, the equipment of broadband and the building construction.
Material: 600D oxford
Size:
JM-B02 360*160*210
SKU: n/a
There are no reviews yet.