The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
-
Clamp Meters
CLAMP METER AC BM 528F
Product DescriptionBM528F AC Digital Clamp meter Technical parametersFunctionsRangeAccuracy(BM528F)DC Voltage200mV/2V/20V/200V/1000V±(0.8%+2)AC Voltage2V/20V/200V/700V±(1.2%+5)AC Current2A/20A/200A/600A±(2%+10)Ω Resistance200/2K/20K/200K/2M/20MΩ±(1%+3)Capacitance20n/200n/2μ/20μ/200μ/2mF±(3%+5)Frequency200/2K/20K/200K/2M/20MHz±(0.5%+3)℃ / ℉-50℃ ~1000℃-58℉~1832℉
±(1%+5)±(1.2%+6)SKU: n/a -
Clamp Meters
UT 205A+
1. 1000A AC current measurement2. 1000V AC/DC voltage measurement3. 600A inrush current measurement (UT206A+)4. Temperature (UT206A+)5. NCV (UT206A+)6. ACV frequency 10Hz~10kHz7. Jaw opening: 45mm8. Resistance / capacitance / frequency measurement9. Auto range / backlight / low battery indication10. Continuity / diode / duty cycle11. MAX/MIN12. Data hold / flashlight / relative mode13. Auto power off14. CAT II 1000V/CAT III 600VSKU: n/a -
Thermal Imagers
UNI-T Uti120T Pocket-Sized Infrared Camera with Real-Time Thermal Image Mini IR Thermal Imager with Large 3.5′′ LCD Touch Display
Thermal ImagersUNI-T Uti120T Pocket-Sized Infrared Camera with Real-Time Thermal Image Mini IR Thermal Imager with Large 3.5′′ LCD Touch Display
Features of UTi120T Thermal Imaging Camera - Thermal Imager has over 10,000 pixels to troubleshoot hot and cold spots
- Adjustable emissivity from 0.10 to 0.99
- Store and share images with optional microSD Card
- Measure temperature range from -20°C to 400°C
- Select color from total 6 palettes to best capture the event
- Support WIFI
- IP54 and 1m drop proof
- Four display mode: thermal, visiable, blending.PIP
- 7 colors palettes
SKU: n/a
There are no reviews yet.