The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Digital Multi Meter
ET 8133 DMM
Product description
3 times/second
Diode: YES
Capacitance: YES
True RMS: YES
Data hold: YES
Backlight: YES
Flashlight: YES
Auto power off: YES (no measurement operation within 15 minutes)
Low battery indication: YES
Environment temperature: 0~40℃, humidity <75%
Storage environment: -20~60℃, humidity <80%
DC voltage:
Range: 200mV/2.000V/20.00V/200.0V/600V
Resolution: 0.0001V/0.001V/0.01V/0.1V/1V
Accuracy: ±(0.5%+3)
Max.: 600V
AC voltage:
Range: 2.000V/20.00V/200.0V/600V
Resolution: 0.001V/0.01V/0.1V/1V
Accuracy: ±(1.0%+3)
Max.: 600V
Capacitance:
Range: 20.00nF/200.0nF/2.000F/200.0F
Resolution: 0.01nF/0.1nF/10nF/100nF
Accuracy: ±5%+3
Max.: 200μF
AC current:
Range: 20mA/200mA, 2A, 10A
Resolution: 0.1mA/0.001A/0.01A
Accuracy:
20mA/200mA/2A: ±(1.0%+3)
10A: ±(1.5%+3)
Max.:
20mA/200mA: 200mA
2A/10A: 10A
DC current:
Range: 20mA/200mA, 2A, 10A
Resolution: 0.1mA/0.001A/0.01A
Accuracy:
20mA/200mA: ±(2.0%+4)
2A: ±(1.0%+5)
10A: ±(2.0%+3)
Max.:
20mA/200mA: 200mA
2A/10A: 10A
Resistance:
Range: 2.000KΩ/20.00KΩ/200.0KΩ/2.000MΩ/20.00MΩ
Resolution: 0.001KΩ/0.01KΩ/0.1KΩ/0.001MΩ/0.01MΩ
Accuracy:
2.000KΩ: ±(1.5%+3)
20.00KΩ: ±(0.5%+3)
200.0KΩ: ±(0.5%+3)
2.000MΩ: ±(1.0%+3)
20.00MΩ: ±(1.5%+3)
Max.: 20MΩ
Continuity: YES
NCV: YES
Frequency response in AC mode: 40Hz~1KHz
LCD size: 45 * 25mm / 1.8 * 1.0in
Item size: 124 * 65 * 26mm / 4.9 * 2.6 * 1.0in
Item weight: 210g / 7.4ounce
Package size: 140 * 100 * 40mm / 5.5 * 3.9 * 1.6in
Package weight: 220g / 7.8ounceSKU: n/a -
Oscilloscopes
UPO2104CS 4 Channels Ultra Phosphor Oscilloscope
Features and Benefits:
1、Sample Rate up to 1GS/s;
2、Channels 4;
3、Bandwidth 100MHz,;
4、Memory Depth 28Mpts (Standard);
5、Waveform Capture Rate up to 50,000wfms/s;
6、With 256 level intensity grading display;
7、Up to 65,000 frames for Waveform Record ,Replay;
8、Support serial bus trigger and decoding;
9、8 inches, TFT LCD,WVGA(800*480);
10、Interface:USB Host, USB Device, LAN, VGA, AUX OUT, 10MHz input/output.SKU: UP21O02CSMHZ -
Soldering Iron
MECHANIC Special Solder Paste XGSP50 [42G] 183℃
Mobile Phone Chips Repair, Computer And Digital Service Industries, High-Precision Circuit Board Smt Soldering, Bga Welding Process, Etc. Solder Paste Lead Solder At Room Temperature Melting Point 183℃ Forming Fast And Easy To Weld Conductive.
SKU: n/a -
Corbon Mono Oxide Meter
Uni-T UT337 Carbon Monoxide Meter
Suitable for use everywhere from in the house to restaurants, offices and industrial areas, the UT337A measures the exact value of carbon monoxide (CO) present in the air. Featuring a built-in sensor integrated into the top of the unit, the UT337A measures CO content from 0-1000ppm with accuracy of ±5% (5ppm) and resolution of 1ppm. The sensor is also designed to adjust rapidly to changes, ensuring you always get a stable, accurate reading. When CO levels exceed a certain threshold, the UT337A will alert the user by using a combination of audible and LED light indicators. The alarm is configurable to the user’s specification and it is also possible to use this meter to calculate temperature values.
SKU: n/a
There are no reviews yet.