TDR-410 Cable Fault Locator
Out of stock
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
₨0
Out of stock
Compare- Location damaged power cables.
- Fault location copper telecom cables.
- Coaxial cable fault location.
- Fault location wiring infrastructure.
- Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
- Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
Dechnical data:
- Ranges Meters: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
- Ranges Feet: 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 14000.
- Range Selection: Manual range control / Auto range.
- Accuracy: 1% of selected range*.
- Resolution: Approx 1% of range.
- Minimum cable lenght: 4m (14ft).
- Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP.
- Velocity Factor: Adjustable from 1% to 99%.
- Output Pulse: 5 volts peak to peak into open circuit.
- Output Impedance: Selectable 25, 50, 75 & 100 Ω.
- Output Pulse: Width 3 ns to 3 µs, Automatic with range.
- Scan Rate: 2 scans/second or scan held, pre set for each range scale.
- Tone Generator: 810 – 1100Hz.
- Battery Life: 30 hours continuous scanning.
- Power Supply: 6 volts 4 x 1.5 AA Alkaline cells, on-screen low voltage indicator.
- Power Down Selectable: 1, 2, 3, 5 minutes or disabled.
- Back Lit Display: 128 x 64 pixel.
- Voltage Protection: 250 volts AC.
- Operating Temp: -10º / 50ºC.
- Storage Temp: -20º +70° C.
- Dimensions: 165 x 90 x 37 mm (6.5 x 3.5 x 1.5 ins).
- Weight: 350 g (12oz).
- Safety: IEC 61010-1, EN 60950.
- EMC: BS/EN 61326-1.
- Water/Dust Proof: IP54
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-410 Cable Fault Locator”
-
Clamp Meters
CLAMP METER AC DC CM 2016
OverviewEssential details- Place of Origin:
-
Guangdong, China
- Brand Name:
-
vici
- Model Number:
-
CM-2016
- Display Type:
-
Digital Only
- Measuring Current Range:
-
60A/600A/800A
- Measuring Voltage Range:
-
600mV/6V/60V/600V
- Measuring Resistance Range:
-
600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ
- Measuring Capacitance Range:
-
6nF/60nF/600nF/6uF/60uF/600uF/6mF/60mF
- Measuring Inductance Range:
-
/
- Operating Temperature:
-
23±5℃
- Dimensions:
-
185*65*32mm
- Weight:
-
200g(including the batteries)
- Backlight display/Clamp light dispaly:
-
YES
- NCV:
-
YES
- Diode test:
-
YES
- clamp open:
-
28mm
- power supply:
-
2pcs 1.5V batteries
- Sampling rate:
-
3 times/second
- AC frequency response:
-
Current 50-60Hz/ voltage 50-400Hz
- Operation method:
-
Auto range
- OEM service:
-
Available
- Product Name:
-
Vicimeter CM-2016 AC/DC 3 5/6 Digital Clamp Meter
SKU: n/a -
Environment Meters
A25F PM2.5 Meter
1. Precise PM2.5 concentration based on pre-calibrated sensors
2. Temperature measurement (°C/°F)3. Humidity measurement4. Emoticon display5. LCD backlight and red backlight alarm6. Battery status, low power, auto power off7. Formaldehyde concentrationSKU: n/a -
-
Clamp Meters
CLAMP METER AC DC CM 2056
Technical data
Basic function
Range
Accuracy
DCV
400mV/4V/40V/400V/1000V
±(0.5%+5)
ACV
400mV/4V/40V/400V/750V
±(1.0%+5)
DCA
400A/1000A
±(2.0%+5)
ACA
400A/1000A
±(2.0%+5)
Resistance
400Ω/4kΩ/40kΩ/400kΩ/4MΩ/40MΩ
±(0.8%+3)
Capacitance
4nF/40nF/400nF/4uF/40uF/200uF
±(3.5%+8)
Frequency
100Hz/1kHz/10kHz/100kHz/1MHz/10MHz
±(0.5%+4)
Temperature
(-40~ 1000) ℃ / (-40 ~1832) ℉
±(1.0%+5)
Special function
CM-2056
NCV test
√
True RMS test
√
Diode test
√
Continuity test
Less than 50Ω±10Ω
Low battery indicator
Approx. less than 2.4 V
Data hold
√
Auto power off
About 15 minutes
Function protection
√
Clamp light
√
Backlight display
√
Input impedance
10MΩ
Sampling rate
3 times/s
AC frequency response
Current 50-60Hz/ voltage 50-400Hz
Operation method
Auto or manual range
Max display
4000
Clamp opens
52mm
Battery
3V (2*AAA battery)
General Characteristic
Meter color
Orange and Black
Meter weight
About 280g (including battery)
Meter size
270×123×50mm
Standard accessory
Test leads, battery, manual, TP01 temperature probe
SKU: n/a
Related products
-
Wire & Cable Testers
UT682 – Wire Tracker
UT682 – Wire Tracker consists of a transmitter and a receiver. It has functions like telephone wire tracking, network wire tracking, cable wire tracking, network wire check, etc. and it produces fast and accurate measurements. UT682 is an ideal tool for personnel to install and maintain network systems with communication lines and integrated wiring circuits.
SKU: n/a -
Wire & Cable Testers
MS6812 Cable Tracker
The Cable Tracker is designed to identify and trace wires or cables within a group without damaging the insulation.For telephone line, it can identify some state in the line, and more convenience to install, debug, maintain telephone line.There is a Sender(MS6812-T) and a Receiver(MS6812-R)included in The Cable Tracker
● Sound and Light Instruction
● Cont and Tone LED LightApplications
– Judge Continuity of the Cables or Wires
– Track the Cables or Wires, and Diagnose the Break Point
– Receive the Tone Signal on the Cables or Wires(Telephone Line)
– Identify the State in the Working Telephone Line(Clear, Ringing, Busy)
– Send a Single Solid or a Dual Alternating Tone to the Target Cables or WiresSKU: n/a -
Wire & Cable Testers
UTP 03 60MHZ PROBE
Attenuation ratio: 1× and 10× optional.
Portable design according to ergonomics.
Integral injection moulding makes the usage more flexible and the oscillograph able to adapt more testing situations.
Safety standards: it has passed the CE Attestation of the European Community.
Compatible with domestic and international digital and analogue oscilloscopes in relevant frequency.
Measurement in intermediate and low-frequency signals.
Accessories included by PP series passive voltage rapier.
Adjusting tool: adjusts compensation capacitance to assure the rapier match with oscillograph.
Contractive-type acuminate hook.
12cm earth wire with an alligator clip.
Locating sleeve adapts to IC testing.
Double-nip wire.
SKU: n/a -
Wire & Cable Testers
UT681L Cable Tester
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
SKU: n/a
There are no reviews yet.