-
×
UT505A Handheld Insulation Resistance Tester
- Vendor:
superworld
Subtotal: ₨45,000
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Availability:
Out of stock
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
₨0
Out of stock
CompareTDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
Two cursors allow to determine the place of two damages simultaneously and the distance between them.
Thanks to the color 3,5” TFT display with a resolution of 320 x 240 pixels, the indication of the location of the damage is precise and the results easier to interpret.
Difficult environment conditions during measurement work are frequent problems encountered by electric installers and maintenance services. Thanks to the unique housing TDR-420 ensure a degree of protection on IP67 level, what means dustproof and protection against water penetration during short-term immersion. Therefore, working in very dusty terrain or accidental contact of the device with water will not affect the correct operation of the reflectometer.
Technical specification
- Measurement ranges: 7, 15, 30, 60, 120, 250, 500 m, 1, 2, 3, 6 km / 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 20000 ft
- Accuracy:1% of selected range
- Resolution: Approx. 1% of selected range
- Min. Cable length: 4 m / (14 ft)
- Velocity of propagation VoP: Adjustable from 10 to…99% or 15…148,5 m/µs
- Output Pulse: 5 Vp-p (open circuit)
- Output Impedance: 25, 50, 75, 100, 120, 200 Ω
- Output Impedance: 3 ns…3 µs (depends of range)
- Scan rate / mode: Up to 3 scans / second (CONT) or single (ONCE)
- Tone generator: 810 … 1110 Hz
- Battery Life: Up to 8 hours of continuous scan
- Power supply: 4 x alkaline batteries 1.5 V type AA or 4 x rechargeable batteries NiMH AA
- Auto-OFF: 1, 3, 5, 10, 15 minutes or deactivated
- Display: Color 3,5” LCD TFT, 320 x 240 pixels
- Voltage protection: 400 V DC / 250 V AC
- Dimensions: 220 x 98 x 58 mm (8.7 x 3.9 x 2.3 inches)
- Weight: 487 g
- Electromagnetic standard compatibility EMC: EN 61326-1
- Water/ Dust Proof: IP67
Nominal condition of use
- Operating temperature: -20..+70°C
- Storage temperature: -30…+80°C at humidity <80%
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-420 Time Domain Reflectometer/ Cable Fault Locator”
-
Insulation Tester
HIGH VOLTAGE INSULATION TESTER KEW 3125A
• Insulation Resistance up to 1TΩ
• Short-Circuit Current up to 1.5mA
• Wide Test Voltage from 250V to 5000V
• Diagnosis Function of PI and DAR
• Newly-designed alligator clip
• It comes with a tough hard case
• Filter function reduces noise interference for obtaining stable measurement
• Large display with Bar Graph indication and backlight
• Live voltage warning
• Safety standard IEC 61010-1 CAT IV 300V / CAT III 600VSKU: n/a -
Digital Multi Meter
ET 8138 DMM
- SLIM – Ultra-Thin Design That Fits Easily In Your Pocket.
- AUTOMATIC – Automatic Range And Automatic Identification.
- DESIGN – It Is Comparable In Size To The 4.7-Inch Mobile Phone. The Design Is Exquisite, Simple And Generous, 3.5 Inch Large Touch Screen.
- COLOUR LCD DISPLAY – Simulation Bar: More Intuitive Display Of Measurements. The Analog Bar Provides Fast And Accurate Digital Representation.
- MODEL – The Winapex 8138 Has A Colour Screen, And Has Hz Function.
SKU: n/a -
Tool Kits
JM 8173 TOOL KIT
Minimum Order Quantity: 20
Pro tech screwdriver set has 69 pieces of screwdriver bits and auxiliary tools to help you complete your maintenance tasks. This pro tech screwdriver set can be used to repair and disassemble precision digital products and household products. JM-8173 pro tech screwdriver set is simple, bright, and transparent for the broad horizon, which brings you a wonderful DIY trip.
SKU: n/a
Related products
-
Wire & Cable Testers
UT18D Voltage and Continuity Tester
1. Auto power off, the conductor to be measured is greater than 12V
2. Phase rotation test3. Continuity test with buzzer and LED indication4. Low battery indication and over voltage prompt5. Flashlight6. Test live voltage without batteries7. Buzzer and silent modes available8. Auto range9. Polarity indicationSKU: n/a -
Wire & Cable Testers
UT681C Cable Tester
Main Features
1. Tests Ethernet cables and telephone lines
2. Equipped with RJ45 interface for Ethernet cable and RJ11 interface for telephone line testing
3. Ethernet cables: Shielded/Unshielded test
4. Visible LED indication
5. Automatically check circuit breakage, short circuit and cross circuit
6. Can toggle between fast and slow speed test modes
7. Single key operation
8. Manual/auto power off (after 10-minute inactivity)
9. Low battery indication
10. Power supplied by 9V layer-built battery
SKU: n/a
There are no reviews yet.