TDR-410 Cable Fault Locator
Out of stock
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
₨0
Out of stock
Compare- Location damaged power cables.
- Fault location copper telecom cables.
- Coaxial cable fault location.
- Fault location wiring infrastructure.
- Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.
- Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
Dechnical data:
- Ranges Meters: 7, 15, 30, 60, 120, 250, 500, 1km, 2km, 3km, 4km
- Ranges Feet: 20, 45, 90, 180, 360, 750, 1500, 3000, 6000, 10000, 14000.
- Range Selection: Manual range control / Auto range.
- Accuracy: 1% of selected range*.
- Resolution: Approx 1% of range.
- Minimum cable lenght: 4m (14ft).
- Sensitivity: Min 3 pixel return at 4km on 0.6mm Ø, PE, TP.
- Velocity Factor: Adjustable from 1% to 99%.
- Output Pulse: 5 volts peak to peak into open circuit.
- Output Impedance: Selectable 25, 50, 75 & 100 Ω.
- Output Pulse: Width 3 ns to 3 µs, Automatic with range.
- Scan Rate: 2 scans/second or scan held, pre set for each range scale.
- Tone Generator: 810 – 1100Hz.
- Battery Life: 30 hours continuous scanning.
- Power Supply: 6 volts 4 x 1.5 AA Alkaline cells, on-screen low voltage indicator.
- Power Down Selectable: 1, 2, 3, 5 minutes or disabled.
- Back Lit Display: 128 x 64 pixel.
- Voltage Protection: 250 volts AC.
- Operating Temp: -10º / 50ºC.
- Storage Temp: -20º +70° C.
- Dimensions: 165 x 90 x 37 mm (6.5 x 3.5 x 1.5 ins).
- Weight: 350 g (12oz).
- Safety: IEC 61010-1, EN 60950.
- EMC: BS/EN 61326-1.
- Water/Dust Proof: IP54
Brand
SONEL
Based on 0 reviews
Be the first to review “TDR-410 Cable Fault Locator”
-
Multimeters
UT18B Voltage And Continuity Testers
UT18 series of test pen with measuring AC and DC voltage (including the three-phase alternating current) measurement, phase of three-phase AC power indicator, on-off test, RCD test, single pen measurement (can determine the zero line or wire), self checking, no battery detection and other functions.
Suitable for: smelting, electronics, manufacturing, defense, electric power, petroleum, chemical industry. Also used to solve complex problems of electronic, factory automation, power distribution and electrical equipment in.SKU: n/a -
Digital Multi Meter
ET 8133 DMM
Product description
3 times/second
Diode: YES
Capacitance: YES
True RMS: YES
Data hold: YES
Backlight: YES
Flashlight: YES
Auto power off: YES (no measurement operation within 15 minutes)
Low battery indication: YES
Environment temperature: 0~40℃, humidity ＜75%
Storage environment: -20~60℃, humidity ＜80%
DC voltage:
Range: 200mV/2.000V/20.00V/200.0V/600V
Resolution: 0.0001V/0.001V/0.01V/0.1V/1V
Accuracy: ±(0.5%+3)
Max.: 600V
AC voltage:
Range: 2.000V/20.00V/200.0V/600V
Resolution: 0.001V/0.01V/0.1V/1V
Accuracy: ±(1.0%+3)
Max.: 600V
Capacitance:
Range: 20.00nF/200.0nF/2.000F/200.0F
Resolution: 0.01nF/0.1nF/10nF/100nF
Accuracy: ±5%+3
Max.: 200μF
AC current:
Range: 20mA/200mA, 2A, 10A
Resolution: 0.1mA/0.001A/0.01A
Accuracy:
20mA/200mA/2A: ±(1.0%+3)
10A: ±(1.5%+3)
Max.:
20mA/200mA: 200mA
2A/10A: 10A
DC current:
Range: 20mA/200mA, 2A, 10A
Resolution: 0.1mA/0.001A/0.01A
Accuracy:
20mA/200mA: ±(2.0%+4)
2A: ±(1.0%+5)
10A: ±(2.0%+3)
Max.:
20mA/200mA: 200mA
2A/10A: 10A
Resistance:
Range: 2.000KΩ/20.00KΩ/200.0KΩ/2.000MΩ/20.00MΩ
Resolution: 0.001KΩ/0.01KΩ/0.1KΩ/0.001MΩ/0.01MΩ
Accuracy:
2.000KΩ: ±(1.5%+3)
20.00KΩ: ±(0.5%+3）
200.0KΩ: ±(0.5%+3)
2.000MΩ: ±(1.0%+3)
20.00MΩ: ±(1.5%+3)
Max.: 20MΩ
Continuity: YES
NCV: YES
Frequency response in AC mode: 40Hz~1KHz
LCD size: 45 * 25mm / 1.8 * 1.0in
Item size: 124 * 65 * 26mm / 4.9 * 2.6 * 1.0in
Item weight: 210g / 7.4ounce
Package size: 140 * 100 * 40mm / 5.5 * 3.9 * 1.6in
Package weight: 220g / 7.8ounceSKU: n/a -
Bags and Box, Tools and Hardware
JM-B02 Professional Orange & Black Tool Bag
High-end tool bag (big size) JM-B02
Assembly and repairing of household appliances, elevator and other large mechanical, the equipment of broadband and the building construction.
Material: 600D oxford
Size:
JM-B02 360*160*210
SKU: n/a -
Spudger
JM OP07 METAL SPUDGER SET
DescriptionItem Description:- Material: Metal
- Brand: JAKEMY
- Features:
– Dual tipped design, various blades for every repair situation.
– Easy to use and handle.
– 3-in-1 metal set.
– Made of stainless steel, sturdy yet still flexible. - Brand:JAKEMY
- Model: JM-OP07
- Material: Stainless steel
- Place of Application: Repair
- Note:
Be careful when using these tools.With their great strength comes the potential to scratch or otherwise damage components that might be better served with plastic tools such as a plastic tool.
SKU: n/a -
Related products
-
Wire & Cable Testers
UT681HDMI Cable Tester
1. Tests HDMI/MINI-HDMI cables
2. Fastline collocation type: A with A, A with C and C with C
3. Checks circuit breakage, short circuit, cross circuit and the missing wire
4. 20 visible LED indicators
5. Can toggle between scan and full display test modes
6. Single key operation
7. Manual/auto power off (after 10-minute inactivity)
8. Low battery indication
9. CE certification
10. Power supplied by 9V layer-built battery
SKU: n/a -
Wire & Cable Testers
UTP 04 100MHZ PROBE
Features Of UNI-T Best Passive Probe 100MHz UTP04:
This passive probe is good oscilloscope accessories, it is suitable for oscilloscope.
Stable performance and not easy to break.
This can provide a professional and accurate measurement.
Widely used, it can satisfy most peoples.
A good helper for instrument engineer.
SKU: n/a
There are no reviews yet.