UT18D Voltage and Continuity Tester
10 in stock
1. Auto power off, the conductor to be measured is greater than 12V
₨12,000 ₨13,000
10 in stock
Compare
| Weight | 0.3 kg |
|---|---|
| Dimensions | 27 × 8 × 3 cm |
Brand
UNI T
Based on 0 reviews
Be the first to review “UT18D Voltage and Continuity Tester”
-
Rework & Soldering Station
YH 939D+ SOLDERING STATION
PARAMETROSMODEL 939D+ RATED VOLTAGE AC 220V±10% 50Hz OUTPUT POWER 75W Constant Temperature Power (High-Speed PID Programmed to Energy Savings) 200W±10％ Withstand voltage and insulation tests AC1500V 0.4A 60S Operating Environment 0～40℃ relative humidity＜80％ Storage environment －20～80℃ relative humidity＜80％ Body size 14.5*12*8CM Weight 2.17KG Work voltage AC 26V±10% 50Hz Temperature range 200℃～480℃ Temperature Stability ±1℃（Static） Display Mode LED Digital Display Calibration Mode PID Digitally Programmed Calibration PID Temperature Calibration Cycle 100MS Heating Core Imported High-Powered Heating Core Tip-to-Ground Impedance ＜2Ω Tip-to-Ground Voltage ＜2mV SKU: n/a -
Rework & Soldering Station
YH 862BD+ REWORK STATION
Machine parameter Rated voltage AC 220V±10% 50Hz Total Power 730W±10％（max） 300℃ Constant Temperature Power (High-Speed PID Programmed
to Energy Savings)
250W±10％ Operating Environment 0～40℃ Relative humidity＜80％ Storage temperature －20～80℃ Relative humidity＜80％ Dimensions 31.5*22*22cm weight 3.5KG Performance Parameter Hot air gun Soldering iron Operating Voltage AC 220V±10% 50Hz AC 26V±10% 50Hz Output power 650W 75W temperature range 100℃～480℃ 200℃～480℃ Air Supply Mode Brushless-Motor Fan — airflow 120L/min(max) — Temperature stability ±2℃ （static） ±2℃ （static） Display Mode Red LED Digital Display Red LED Digital Display Calibration Mode PID Digitally Programmed Calibration
PID Digitally Programmed Calibration
Temperature correction PID digital program proofreading
PID digital program proofreading
SKU: n/a -
Clamp Meters
UT 207 CLAMP METER
1. 1000A AC/DC current measurement, 3 times/s sampling rate 2. True RMS 3. Inrush current 4. Zeroing function 5. Full icon display 6. MAX/MIN 7. Data hold; Duty cycle 8. Auto power off and low battery indication 9. Diode; Continuity buzzer; Input Impedance for DCV
SKU: n/a -
Clamp Meters
UT 208 CLAMP METER
1. 1000A AC/DC current measurement, 3 times/s sampling rate
2. True RMS3. Inrush current4. Zeroing function5. Full icon display6. MAX/MIN7. Data hold; Duty cycle8. Auto power off and low battery indication9. Point contact temperature probe10. Diode; Continuity buzzer; Input Impedance for DCVSKU: n/a
Related products
-
Wire & Cable Testers
TDR-410 Cable Fault Locator
-
Features:
- automatic or manual mode:
- the automatic fault location (AFL),
- mode with manual range selection and sensitivity,
- single measurement triggered manually or scanning continuous,
- 11 available ranges from 7 m to 4000 m selected in manual mode or matched automatically,
- maximum length of cable up to 4000 m one end of the cable,
- “Dead zone” measure limited to 0.5 m,
- 2.5 “LCD screen with backlight,
- scan automatically or manually trigger,
- sensitivity set manually or automatically adjusted,
- adjustable impedance matching,
- propagation coefficient adjustment 1% to 99%,
- waterproof and resistant to mechanical housing.
- small size and weight.
- economical power system – 30 hours of continuously scan on one battery set..
Accessories:
- 0,6 m double-wire lead: WAPRZ0X6DZBB
- red crocodile clip: WAKRORE20K02
- Krokodylek czarny: WAKROBL20K01
- cover M-2: WAFUTM2
- automatic or manual mode:
SKU: n/a -
-
Wire & Cable Testers
LKZ-1000 Wires and pipe locator
- Passive or active modes of tracing.
- Detection of underground live wires.
- Detection of underground wires with no voltage (radio mode).
- Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).
- Tracing metallic or non-conductive pipes using an additional probe.
- Tracing non-conductive pipelines using a “floating” probe.
- Tracing a determined cable.
- Determining the depth of a cable.
SKU: n/a -
Wire & Cable Testers
TDR-420 Time Domain Reflectometer/ Cable Fault Locator
Product features
- Possibility damage-free location of impedance changes of tested cables and wires such as:
- shorted conductor,
- open conductor / end of cable – useful during the inventory of warehouses and stores,
- splice,
- splitter,
- water ingress,
- wet splice,
- bridge tap
- or other changes.
- Single measurement mode ONCE,
- Continuously measurement mode CONT,
- Tone signal generator TONE,
- Two cursors to mark two places of damage along with an indication of the distance between them,
- Built-in HELP function for easier interpretation of the reflectogram,
- 11 available measuring ranges from 7 m to 6000 m,
- „dead zone” limited to 0.6 m,
- Color 3,5” LCD TFT display with resolution 320 x 240 pixels,
- manually set of sensitivity in 8 steps GAIN,
- output impedance regulation up to 200 Ω (possibility of measuring pre-insulated pipes),
- Velocity of Propagation set in range from 10% to 99%,
- tight and durable housing with IP67 ingress protection degree.
- Small size and weight.
SKU: n/a - Possibility damage-free location of impedance changes of tested cables and wires such as:
There are no reviews yet.