The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Digital Micro Ohm Meter
UT620A Digital Micro Ohm Meter
Features of UT620A Digital Micro Ohm Meter
● Comparison measurement with upper and lower limits● Wire length measurement (m/ft)● Built-in Lithium battery● 1000-group data storage● Improved measurement method which improves accuracy by counter-balancing contact resistance of leads● Data transmission between USB and PC● Data hold● LCD backlight● Zeroing function, relative mode● IND resistance measurement modeSKU: n/a -
Tool Kits
JM SK05
Feature:
PVC plastic material, environmental friendly, not easy to deformation, high oil-resistant and corrosion-resistant.
Brand new and high quality.
Suitable for screen separation of mobile phones and tablets.
ABC industrial plastic material, more durable and higher deformation-resistant than usual plastic.
Heavy duty suction cup.
Can be reused many times.
Used to remove phone and tablet glass panels.
Ergonomic design,easy to use.SKU: n/a -
Clamp Meters
CLAMP METER AC DT3266
DT3266L AC/DC Mini Pocket Handheld Digital Clamp Meter Voltage Current Resistance Tester Multimeter
Features :
- 3 1/2 digit LCD screen, the maximum display value is 1999.
- A multi-purpose clamp meter can measure AC/DC voltage and resistance, etc.
- Low voltage indication and overload protection.
- Diode and continuity measurement.
- High resolution of 1mA minimum force.
- Small and portable to carry and use.
- Data retention for easier reading.
Specifications :
- Color : Black + Yellow
- Material : Plastic
- DC Voltage : 600V ±(0.8%+3dgt)
- AC Voltage : 750V ±(1.2% +5dgt)
- AC Current : 20A-200A-400A ±(2%+5dgt)
- Resistance : 2K-200K-2MΩ ±(1.0%+3dgt)
- Power Supply : 2 x AAA 1.5V Batteries (Not included)
- Maximum Display : 1999
- Jaw Diameter : 30.8mm
- Display Size : 35 x 17mm
- Item Size : 17.3 x 5.2 x 2.5cm / 6.8 x 2 x 0.98in
- Item Weight : 120g / 4.24oz
- Package Size : 17.8 x 10 x 3cm / 7 x 3.94 x 1.18in (L x W x H)
- Package Weight : 187g / 6.59in
- GW:0.2KG
Note :
This meter can’t measure DC current.
Package includes :
- 1 x Clamp Meter
- 1 x Test Lead
Best online shopping website for Portable Handheld Digital Clamp Meter DT3266L AC DC Multimeter Voltage Current Resistance Tester at cheap price in Lahore, Islamabad, Karachi, Faislabad, Multan, Quetta, Sukkur, Peshawar, Rawalpindi, and all over Pakistan
SKU: n/a
There are no reviews yet.