The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Insulation Tester
MIC-15k1 ,15kV Insulation Quality Analyzer
Features:
- Diagnostics of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD, widened with thepartial discharge (PD) indicator for every each of these measurements.
- It allows testing the electrical durability of the tested object – breakdown voltage indication.
- High resistance to electromagnetic interferences guarantees uninterrupted work in power stations and close to high voltage transmission lines up to 1200 kV AC and 500 kV DC.
- The function of smooth voltage rise in time (RT – Ramp Test) allows to state the partial discharges in the facility and to carry out a partial location of their occurrence.
- Efficient converter with a power of ~150 W that enables insulation burnout, allowing for pinpointing the location of cables and wires short circuit using one of the following:
- visual method (if power cables are visible along the entire length),
- reflectometric methods, seismic-acoustic waves detector, or with A-frame to indicate direction of the fault (the conductor must be buried in the ground with earth direct contact).
- Compatible with external software.
SKU: n/a -
IR Resolution
UNI-T UTi320E High IR Resolution 320×240 Professional Handheld Thermal Imager with PC,WiFi and App Connect Support Data Analysis and Real Time Display
IR ResolutionUNI-T UTi320E High IR Resolution 320×240 Professional Handheld Thermal Imager with PC,WiFi and App Connect Support Data Analysis and Real Time Display
Screen Display 3.5″IPS Temeperature Range -40°~400° IR Resolution(Pixels) 320×240 Visible Camera Resolution 2MP Field of View(FOV) 56°x 42° Spatial Resolution(IFOV) 3mrad Frame Rate 9Hz Thermal Sensitivity(NETD) 65mK Measurement Accuracy ±2° or ±2%
whichever is greaterEmissivity 0.01-0.99 Adjustable Spectral Range 8~14μm Foucs Foucs Free Digital Zoom 2x, 4x Palattes 7(Iron, Rainbow, White Hot, Red Hot, Black Hot, Lava, Rainbow HC) Display Modes Thermal,Visible,Fusion,PIP Mesurement Mode Center Pot,High/Low Temp Pot,ROI Temperature Analysis (Point 5 /Line 1 /Area 6 ) total 6 tools Battery Li-ion battery pack 5200mAh Battery Type Replaceable Battery Life ≥ 4hours Charging Time ≤5Hours Communication interface Type-C IP Rating IP54 Drop Proof 2m Functions Flashlight √ Tripod Hole √ Auto tracking of High/Low Temperature √ Auto Alarm of High/Low Temperature √ Image Capture √ Video Recording × Voice Recording × RIO(Eliminates Interference) √ Isotherm √ PC Real Time Image Transmisstion √ PC Analysis Software √ Wifi Photo Download √ Wifi Real Time Display × Bluetooth × Mobile APP √ GPS × Laser/Distance Measurement × SKU: n/a
There are no reviews yet.