The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Earth Ground Resistance Testers
MRU-30 Earth Resistance and Resistivity Meter
-
It allows to take the measurements of:
- earthing resistance using auxiliary electrodes,
- earthing resistance using auxiliary electrodes and clamp (for measurements of multiple earthing),
- earthing resistance using double clamps for measuring multiple earthing without underground connections.
- ground resistivity (Wenner method),
- continuity of equipotential bondings and protective
- conductors (meeting the requirements IEC 60364) with auto-zero function – with current 200mA.
Additionally:
- measurement of resistance of auxiliary electrodes RS and RH,
- measurement of interference voltage,
- measurement in the presence of interference voltage in the power network
- with frequency 50Hz, 60Hz,
- selection of maximum measuring voltage (25V and 50V),
- introducing the distance between the electrodes for the resistivity in metres (m) and feet (ft),
- memory of 990 measurements (10 banks of 99 cells each),
- calibration of clamp used,
- data transmission to the computer (USB),
- indication of battery state.
SKU: n/a -
-
Multimeters
UT181A True RMS Datalogging Multimeter
1. Trend capture
2. Data logging: 200003. Data comparison4. 3.5-inch 64k color TFT LCD5. Dual temperature measurement6. Low pass filter7. 2200mAh Li-ion battery8. Real time and date9. Peak hold10. Bluetooth/APP11.USB interface cable /PC software CD12. IP65SKU: n/a -
Thermal Imagers
UNI-T UTi260B Handheld Thermal Imaging Camera Real Time Thermal Imager with Buzzer Flashlight Alarm 2.8′′ LCD Display
Thermal ImagersUNI-T UTi260B Handheld Thermal Imaging Camera Real Time Thermal Imager with Buzzer Flashlight Alarm 2.8′′ LCD Display
Features of UTi260B Thermal Imaging Camera - 2.8″ TFT screen
- Infrared resolution: 256 x 192
- Temperature measurement range: -15ºC~550ºC
- Photograph function with SD card storage
- PC analysis software
- Buzzer/flashlight alarm
- Real-time image transmission
- Auto capture of High/Low temperature
- Flashlight
- 1/4″ tripod mounting hole
- IP65/2m drop proof
SKU: n/a -
Rework & Soldering Station
YIHUA 9936 Portable Soldering Station
Standard accessory
Main unit 1set
Soldering iron handle (include iron tips and heater) 1pc
Iron holder 1pc
Clean sponge 1pc
Manual 1pc
Application Scope
- Production lines for electronic products ,
2. Repair industry for mobile phone.
3. SMD components requiring the highest precision
SKU: n/a - Production lines for electronic products ,
There are no reviews yet.