-11%

Battery Load Tester – BT 100A


  • Sleek Design Silver Metal Body

  • Easy To Use
  • Convenient portable size and easy-to-read scales
  • Tests batteries on or off the car in just 10 seconds
  • Determines good/bad status with an extra-large display with zero adjust
  • Determines state-of-charge cranking and charging volts
  • Works on both 6 Volts and 12 volts batteries

5,264 5,923

Compare
KEY FEATURES
  • Sleek Design Silver Metal Body
  • Easy To Use
  • Convenient portable size and easy-to-read scales
  • Tests batteries on or off the car in just 10 seconds
  • Determines good/bad status with an extra-large display with zero adjust
  • Determines state-of-charge cranking and charging volts
  • Works on both 6 Volts and 12 volts batteries
Category:
Weight 0.7 kg
Dimensions 14 × 7 × 5 cm

TITAN BATTERY TESTER BT 100 A CAN BE USED TO TEST 6V AND 12 BATTERY SYSTEMS.IT CAN GENERATE LOAD JUNK LOAD UPTO 90A DC.UPTO 200A BATTERIES CAN BE TESTED.

WHAT’S IN THE BOX?

1 x BT 100 A
1 x MANUAL

Brand

TITAN

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Battery Load Tester – BT 100A”

There are no reviews yet.

  • A10T Temperature Humidity Meter

    0 out of 5
    (0)

    Main Features

    1. Sampling time: 10s

    2. Clock function: 12/24 hour mode

    3. Alarm function: Rings up to 60s

    4. Temperature measurement + Humidity measurement+ Time

    5. Temperature testing range: -10℃~50℃(14℉~122℉); Accuracy: ±1℃(±1.8℉)

    6. Humidity testing range: 10~99%RH; Precision: ±5%RH

    7. Environmental comfort rating: Comfort, wet, dry

    SKU: n/a
  • CMM-40 Industrial Multimeter

    0 out of 5
    (0)

    The most important features of CMM-40 are:

    • autoranging/manual range selection,
    • „DATA HOLD” function, for holding measured values,
    • „REL” function, which allows you to make measurements relative to a stored reference value,
    • „MAX/MIN” function,
    • „PEAK HOLD” function,
    • memory for 2000 measurement resultS,
    • continuity test with acoustic signalling (beeper),
    • „AUTO-OFF” function,
    • display 4¾ digits (40000 max),
    • double molded, waterproof casing.
    SKU: n/a
  • UT372 Tachometer

    0 out of 5
    (0)
    SKU: 10000
  • ,

    Jakemy JM-Z19 8X Optical Magnifier

    0 out of 5
    (0)

    1.the magnifier is make by ABS and resin.
    2.Working need 3 pcs AAA battery to light the 2 LED(not included in the package).
    3.Diameter:37MM
    4.Suitable:PCB repair,repair electronic etc.

    SKU: n/a
  • UT620 Series Digital Micro Ohm Meters

    0 out of 5
    (0)

    UT620 series are used to measure DC low resistance through 4-wire method. Some of its features are: Comparison function to determine if the device is in good condition, unknown wire length calculation (FT/M); two-way data transmission by USB interface; built-in rechargeable lithium battery. UT620 can be used in narrow space for on-site troubleshooting, such as metal coating resistance/motor and small transformer winding resistance measurement, earth system joints/welding points/power distribution cabinet bus and lead connection inspection and more.

    SKU: UN62B0TUOM
  • UTG9002C-II Function/Arbitrary Waveform Generator

    0 out of 5
    (0)

    1. Output waveforms: Sine, square, ramp, pulse, noise, DC, arbitrary

    2. Output frequency range: Sine/square, 2MHz
    3. High-accuracy, broad-band 6 bit frequency counter, range: 100mHz~100MHz
    4. EBTN LCD screen
    SKU: n/a