-
×
Titan Digital Clamp Meter Multimeter Ampere Meter
- Vendor:
superworld
Subtotal: ₨3,575
-29%
Battery Testers
Battery Load Tester – BT 100D
Availability:
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Clamp Meters
UT222 2500A ACA DCA Digital Clamp Meters
UT222 are stable and safe 3 5/6 digit AC&DC digital clamp meters.It is perfectly designed with over-load protection for all ranges and the unique structure, making it a superb professional meter especially for electricians.
An ideal tool for the maintenance and troubleshooting needed in metallurgy, manufacturing, petroleum, electric power, chemical industry, etc;SKU: n/a -
Voltage Detector
UT12E-US AC Voltage Detector
features:
1. Auto power off
2. Buzzer
3. LED indication
4. IP 67
5. AC voltagedetection
6. High/Lowvoltage mode
7. Vibration modeApplications:
Low voltage mode: Low-voltage motor (<90V), audio systems, arc welding machines,underground mining lighting, cables with thick insulation layer and other weakelectromagnetic AC signals.
High voltage mode: Urban electric supply and three-phase systems (90~1000V). Forexample, power distribution units, electrical panels, electrical appliances.SKU: n/a -
LCR Meter
MS8910 Smart SMD Tester (R/C)
The Tester is a handheld and battery operated very convenient small Tool that is specially used to measuring SMD (Surface Mounting Device), there are Chip type resistor, Chip type capacitor, and diode. Moreover, the Tester also has the continuity checking function.
● Display 3000 counts
● Auto Ranging
● Auto Power Off
● Data Hold
● Low Battery Display
● Auto Scanning
● Diode Check Open Voltage 2.8V
● Diode Testing Current 2mA
● Continuity Buzzer <30ΩSKU: n/a
Related products
-
Battery Testers
UNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Battery TestersUNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Model UT3513 Resistance range 20m Q/200m Q/2Q/20Q /200 Q/2kQ/20kQ Resolution 1 u Q/10 u Q/100 u Q/lmO/lOmQ/lOOmQ/1 Q/10Q/100Q Test current 1A/1A/100mA/10mA/1mA/1mA/100 uA/10 u A/l uA Testing terminal opencircuit voltage ＜1V/＜1V/＜1V/＜1V/＜5V/＜5V/＜5V/＜5V/＜3V/ Measured parameter DC resistance Basic accuracy Slow: 0. 1%; Medium: 0. 2% Maximum reading 22000 Range mode Auto/Manual/nominal Calibration Short-circuit full range zeroing Sorting function 3types of resistance and voltage input: exceeds upper limit/exceeds lower limit/within the range,2 types of sorting result output: PASS/FAIL Comparing method Absolute tolerance, percentage tolerance, direct-reading comparison Trigger mode Internal, external Test terminal Four-terminal measurement Button functions Lock 一一 keyboard lock, OK 一一 screenshot System setup Language: Chinese/English, key tone setting Interfaces & protocols Handler interface, RS232, USB DEVICE and USB HOST communication interface,SCPI and Modbus protocol Upper computer software V Power AC 100~240V 50/60Hz Display 4.3-inches LCD SKU: n/a -
Battery Testers
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
SKU: n/a -
-
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a
There are no reviews yet.