Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Clamp Meters
CLAMP METER AC DC CM 2056
Technical data
Basic function
Range
Accuracy
DCV
400mV/4V/40V/400V/1000V
±(0.5%+5)
ACV
400mV/4V/40V/400V/750V
±(1.0%+5)
DCA
400A/1000A
±(2.0%+5)
ACA
400A/1000A
±(2.0%+5)
Resistance
400Ω/4kΩ/40kΩ/400kΩ/4MΩ/40MΩ
±(0.8%+3)
Capacitance
4nF/40nF/400nF/4uF/40uF/200uF
±(3.5%+8)
Frequency
100Hz/1kHz/10kHz/100kHz/1MHz/10MHz
±(0.5%+4)
Temperature
(-40~ 1000) ℃ / (-40 ~1832) ℉
±(1.0%+5)
Special function
CM-2056
NCV test
√
True RMS test
√
Diode test
√
Continuity test
Less than 50Ω±10Ω
Low battery indicator
Approx. less than 2.4 V
Data hold
√
Auto power off
About 15 minutes
Function protection
√
Clamp light
√
Backlight display
√
Input impedance
10MΩ
Sampling rate
3 times/s
AC frequency response
Current 50-60Hz/ voltage 50-400Hz
Operation method
Auto or manual range
Max display
4000
Clamp opens
52mm
Battery
3V (2*AAA battery)
General Characteristic
Meter color
Orange and Black
Meter weight
About 280g (including battery)
Meter size
270×123×50mm
Standard accessory
Test leads, battery, manual, TP01 temperature probe
SKU: n/a -
-
Bags and Box, Tools and Hardware
JM-B02 Professional Orange & Black Tool Bag
High-end tool bag (big size) JM-B02
Assembly and repairing of household appliances, elevator and other large mechanical, the equipment of broadband and the building construction.
Material: 600D oxford
Size:
JM-B02 360*160*210
SKU: n/a
Related products
-
Battery Testers
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
SKU: n/a -
-
Battery Testers
UT673A Battery Testers
Features of UT673A Battery Testers
Certifications: CE, UKCA, FCC
● 12V cranking lead acid battery test
● 12/24V charging or cranking system test● Display battery capacity, voltage, resistance and life● Four-termina Kelvin test● 10 types of battery standards● Language option (Chinese/English)● Test without battery disassembly● LED color indication for test result (UT673A)● Print on-line and real-time test reports (UT675A)● USB data transfer (UT675A)SKU: n/a -
Battery Testers
UT675A Battery Testers
Features of UT675A Battery Testers
Certifications: CE, UKCA, FCC
● 12V cranking lead acid battery test
● 12/24V charging or cranking system test● Display battery capacity, voltage, resistance and life● Four-termina Kelvin test● 10 types of battery standards● Language option (Chinese/English)● Test without battery disassembly● LED color indication for test result (UT673A)● Print on-line and real-time test reports (UT675A)● USB data transfer (UT675A)SKU: n/a -
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a
There are no reviews yet.