-
×
JM-8107 38 in 1 Screwdriver Set
- Vendor:
superworld
Subtotal: ₨1,840
-29%
Battery Testers
Battery Load Tester – BT 100D
Availability:
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Clamp Meters
CLAMP METER AC BM 5268
BM5268 AC Digital Clamp meter Technical parameters Functions Range Accuracy BM5268 DC Voltage 400mV/4V/40V/400V/600V ±(0.8%+2) AC Voltage 4/40/400/600V ±(1.2%+5) AC Current 4/40/400/600A ±(2%+10) Ω Resistance 400/4K/40K/400K/4M/40MΩ ±(1%+3) Capacitance 10n/100n/1μ/10μ/100μ/1m/10mF ±(3%+5) Frequency 10/100/1K/10K/100K/1M/30MHz ±(0.5%+3) ºC/ºF -50ºC~1000ºC ±(1%+5) -58ºF~1832ºF ±(1.2%+6) Functions Range Accuracy True RMS √ Manual range √ Automatic range √ Auto power OFF About 10minutes √ Auto power OFF/Manually turn it off √ Diode Test √ VHZ voltage measuring frequency √ Phase line recognition √ Continuity Testing √ Data hold √ INR Surge voltage √ low Battery indication √ Overload protection √ Greatest display 1999 √ Jaw Size Φ30mm General Features Power DC9V(6F22)Battery Color Gray+Red Weight About 220g Size 195×64×35mm Standard accessories Multimeter leads+Batteries+Temperature Sensor Standard Pack Color Box,User Manua Safety rating EN61010-1,CAT.II 600V SKU: n/a -
-
Battery Testers
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
SKU: n/a -
Related products
-
Battery Testers
UT675A Battery Testers
Features of UT675A Battery Testers
Certifications: CE, UKCA, FCC
● 12V cranking lead acid battery test
● 12/24V charging or cranking system test● Display battery capacity, voltage, resistance and life● Four-termina Kelvin test● 10 types of battery standards● Language option (Chinese/English)● Test without battery disassembly● LED color indication for test result (UT673A)● Print on-line and real-time test reports (UT675A)● USB data transfer (UT675A)SKU: n/a
There are no reviews yet.