Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
DC Power Supplies
YIHUA 3010D DC Power supply
This model has compact design with all metal construction.
1.This unit now features a Dual LED display with highly accurate LED digital readout.
2.Maximum output is 30V at 10A.
- High stabilized output voltage.
- Short circuit protection.
5.Over loading and current protection.
SKU: n/a -
Clamp Meters
CLAMP METER AC BM 818
Features: 1. Multifunctional, can measure ac/dc voltage, ac current, resistance, capacitance, ncv, diode, continuity. 2. Portable Design: Small and pocketable, easy to carry. 3. Stable performance, high precision, large LCD backlight screen, large capacitance range. 4. Safe and reliable, non-contact ncv tester. 5. There is a tinnitus indicator.SKU: n/a -
Multimeters
CMM-10 Multimeter
- Autoranging/manual range selection.
- DATA HOLD function, for holding measured values.
- REL function, which allows you to make measurements relative to a stored reference value.
- Continuity test with acoustic signalling (beeper).
- AUTO-OFF function.
- Display 3 7/8 digits (5000 max).
SKU: n/a
Related products
-
Process Celibrators
UT715 Multifunction Loop Process Calibrator
Features of UT715 Multifunction Loop Process Calibrator
Certifications: CE, UKCA
● Step/ramp functions
● Source and measure accuracy up to 0.02%● Rechargeable battery● Contrast adjustment● Auto power off (Time adjustable)● Stores and recalls setups● USB communication● Provides 24V loop power to transmitter while conducting mA current measurement at the same timeSKU: n/a -
Battery Testers
Battery Load Tester – BT 100A
-
Sleek Design Silver Metal Body
- Easy To Use
- Convenient portable size and easy-to-read scales
- Tests batteries on or off the car in just 10 seconds
- Determines good/bad status with an extra-large display with zero adjust
- Determines state-of-charge cranking and charging volts
- Works on both 6 Volts and 12 volts batteries
SKU: n/a -
-
Digital Multi Meter
UNI-T UTi320V Thermal Image
Technical Specifications of UTi320V Thermal Image:
Specifications Model UTi320V Temperature range -20~350℃ -4℉~662℉ Temperature accuracy ±2℃ or ±2% (whichever is greater) Temperature resolution 0.1℃/0.18℉ Thermal resolution 320×240 Temperature coefficient ± 0.1/℃ or ± 0.1%/℃ (whichever is greater) Visible light resolution 640×480 Emissivity Adjustable (0.01-1.00), 0.98 in default Reflectivity Reflectivity correction (adjustable background temperature) Palettes White hot, iron red, arctic, rainbow 2, hot iron, rainbow 1 High/low temperature tracking √ High/low temperature alarm √ Image blending/Picture in picture √ WIFI mode Connects to PC software and moblie phone App Lens 7mm Focus Focus free FOV 42.5°×32.5° NETD ≤60mK Image frequency 50Hz Digital zoom ×2, ×4 General Characteristics Power 7.4V 2300mAh Li-ion battery Display 3.5-inches TFT LCD Product color Red and grey Product net weight 1.8kg (Package) Product size 258mm x 98mm x 90mm Standard accessories Li-on battery x 2, USB power supply with multi plugs,
wrist strap, adaptor×5, SD card, USB cable, PC software CDStandard individual packing Gift box, tool box, English manual Standard quantity per carton 1pcs Standard carton measurement 410mm x 265mm x 180mm Standard carton gross weight 2.2kg SKU: n/a
There are no reviews yet.