Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareThe BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
| Weight | 0.7 kg |
|---|---|
| Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Brand
TITAN
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Thermal Imagers
KT-80 Thermal Imager
Features and benefits of Sonel KT:
- Friendly UI, easy to use without training,
- Affordable as entry level diagnostic tool,
- Removable large capacity Li-ion battery,
- 4 hour working time,
- 3,5’’ large screen with no image cropping, high brightness screen to show image with no detailed information lost even outdoor or in highlight,
- Rugged and compact design, metal internal structure,
- Standard Micro USB interface for data transmission and charging,
- Wi-Fi connection (Optional).
SKU: n/a
Related products
-
Battery Testers
UNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Battery TestersUNI-T UT3513 DC Resistance Tester Microohmmeter 4.3 Inch LCD Screen Cable/Coil/Motor Resistance Test
Model UT3513 Resistance range 20m Q/200m Q/2Q/20Q /200 Q/2kQ/20kQ Resolution 1 u Q/10 u Q/100 u Q/lmO/lOmQ/lOOmQ/1 Q/10Q/100Q Test current 1A/1A/100mA/10mA/1mA/1mA/100 uA/10 u A/l uA Testing terminal opencircuit voltage ＜1V/＜1V/＜1V/＜1V/＜5V/＜5V/＜5V/＜5V/＜3V/ Measured parameter DC resistance Basic accuracy Slow: 0. 1%; Medium: 0. 2% Maximum reading 22000 Range mode Auto/Manual/nominal Calibration Short-circuit full range zeroing Sorting function 3types of resistance and voltage input: exceeds upper limit/exceeds lower limit/within the range,2 types of sorting result output: PASS/FAIL Comparing method Absolute tolerance, percentage tolerance, direct-reading comparison Trigger mode Internal, external Test terminal Four-terminal measurement Button functions Lock 一一 keyboard lock, OK 一一 screenshot System setup Language: Chinese/English, key tone setting Interfaces & protocols Handler interface, RS232, USB DEVICE and USB HOST communication interface,SCPI and Modbus protocol Upper computer software V Power AC 100~240V 50/60Hz Display 4.3-inches LCD SKU: n/a -
Digital Multi Meter
UNI-T UTi320V Thermal Image
Technical Specifications of UTi320V Thermal Image:
Specifications Model UTi320V Temperature range -20~350℃ -4℉~662℉ Temperature accuracy ±2℃ or ±2% (whichever is greater) Temperature resolution 0.1℃/0.18℉ Thermal resolution 320×240 Temperature coefficient ± 0.1/℃ or ± 0.1%/℃ (whichever is greater) Visible light resolution 640×480 Emissivity Adjustable (0.01-1.00), 0.98 in default Reflectivity Reflectivity correction (adjustable background temperature) Palettes White hot, iron red, arctic, rainbow 2, hot iron, rainbow 1 High/low temperature tracking √ High/low temperature alarm √ Image blending/Picture in picture √ WIFI mode Connects to PC software and moblie phone App Lens 7mm Focus Focus free FOV 42.5°×32.5° NETD ≤60mK Image frequency 50Hz Digital zoom ×2, ×4 General Characteristics Power 7.4V 2300mAh Li-ion battery Display 3.5-inches TFT LCD Product color Red and grey Product net weight 1.8kg (Package) Product size 258mm x 98mm x 90mm Standard accessories Li-on battery x 2, USB power supply with multi plugs,
wrist strap, adaptor×5, SD card, USB cable, PC software CDStandard individual packing Gift box, tool box, English manual Standard quantity per carton 1pcs Standard carton measurement 410mm x 265mm x 180mm Standard carton gross weight 2.2kg SKU: n/a
There are no reviews yet.