The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Insulation Tester
MIC-2501,2500V Insulation Resistance Meter
Electrical safety:
- type of insulation: double, in acc. with EN 61010-1 und IEC 61557
- measurement category: IV 600 V (III 1000 V) in acc. to EN 61010-1
- case protection rating in acc. with EN 60529: IP65
Other technical specifications:
- power supply of the meter SONEL L-1 NiMH 9,6 V; DC 12 V 2,5 A
- weight of the meter: approx. 0,9 kg
- dimensions: 200 x 180 x 77 mm
- display: LCD segment display
- measurement results memory: 990 cells, 11880 records,
- transmission of measurement results: USB
SKU: n/a -
Clamp Meters
Titan Digital Clamp Meter Multimeter Ampere Meter
3 1/2 digits LCD with a Max. Reading of 1999
2) Diode and Buzzer function
3) Low battery indication
4) Overload protection
5) Data hold for easy reading
* Specification:
1) DC voltage: 600V (?1.0%)
2) AC voltage: 450V ( ?1.2% )
3) OHM: 200K? (?1.0%)
4) ACA: 20-400A (?2.0%)
5) Power supply: (AAA) 1.5V?2
6) Data hold: YES
7) Dimension 150L?63W?27.5Hmm
Weight 121g
SKU: n/a -
LCR Meter
UNI-T UT622E Handheld LCR Meter
Features of UNI-T UT622E Handheld LCR Meter:
- Up to 0.1% measurement accuracy
- High-brightness white backlight
- Ultra-low power consumption and long battery life (8 hours)
- Maximum test speed: 20 times/s
- Constant 100Q output impedance
- Data hold and recording mode
- Standard Mini-USB interface, SCPI command set
SKU: n/a -
Clamp Meters
UT206A+
1. 1000A AC current measurement
2. 1000V AC/DC voltage measurement
3. 600A inrush current measurement (UT206A+)
4. Temperature (UT206A+)
5. NCV (UT206A+)
6. ACV frequency 10Hz~10kHz
7. Jaw opening: 45mm
8. Resistance / capacitance / frequency measurement
9. Auto range / backlight / low battery indication
10. Continuity / diode / duty cycle
11. MAX/MIN
12. Data hold / flashlight / relative mode
13. Auto power off
14. CAT II 1000V/CAT III 600VSKU: n/a
There are no reviews yet.