The BT-100D 100+ Amp Digital Battery Load Tester is microprocessor controlled. It makes for an easy and accurate load test with no need to time yourself to get accurate results. Bright, LED Digital Display indicates both voltage and test results. A unique 3-Step Design provides LED polarity check function, battery load test and charging system test readout. Automatically Turns Off the Load after 10 seconds and locks the voltage. Super-Grip Battery Clamps are heavy-duty and color-coded. Baked Enamel, Steel Case to keep cool. Rubber Insulated Carrying Handle–for comfort and safety. Checks both Battery and Charging System.
Battery Load Tester – BT 100D
7 in stock
- 100 Amp Digital Battery Load Tester
- Microprocessor Control–makes for an easy and accurate load test with no need to time yourself
- Bright, LED Digital Display–indicates both voltage and test results
- Unique 3-Step Design–LED polarity check function, battery load test and charging system test readout
- Super-Grip Battery Clamps–heavy-duty and color-coded
- Baked Enamel, Steel Case–ventilated to keep cool
- Rubber Insulated Carrying Handle–for comfort and safety
- Checks both Battery and Charging System
₨5,000 ₨7,000
7 in stock
CompareWeight | 0.7 kg |
---|---|
Dimensions | 15 × 8 × 6 cm |
12 Volt Battery Analysis
Press “START TEST” & wait for 10 seconds.
Once automatic test cycle is completed, your test results will be:
1. GREEN LIGHT = OK):
Battery capacity is good. May or may not be fully charged.
Determine state of charge by checking specific gravity (use hydrometer). If gravity is less than full charge, check for possible charging system trouble or electrical drain. Recharge battery to fully charged level.
2. GREEN + YELLOW LIGHT = OK BUT WEAK):
Review the load test result with the comparison chart on the tester cover to see if this battery is “OK” or not. If it is “OK”, go up to 1ST “OK” state. If it is not, go down to 3rd “WEAK” state.
3. YELLOW LIGHT = WEAK):
Battery capacity is unsatisfactory. Battery may be either: (1) defective or (2) partially discharged. To determine which, check specific gravity. If gravity is over 1.225, battery is considered defective. If gravity is under 1.225, recharge battery and re-test. If cell-to-cell gravity varies more than 0.025 (25 points), cell trouble may exist. If charging does not bring gravity to fully charged level, the battery is either sulfated or has lost active material.
4. RED LIGHT = BAD):
Battery may be defective (e.g. a bad cell).
NOTE: If pre-test battery voltage is below 12.3V, tester will not allow and should not perform the load test. Please fully charge battery and retest.
Based on 0 reviews
Be the first to review “Battery Load Tester – BT 100D”
-
Usb Tester
UT330TH/UT330THC USB Dataloggers
Features of UT330TH/UT330THC USB Dataloggers
Certificates: CE, UKCA, RoHS
● 64000 groups data storage
● Auto record time setup● Adjustable logging interval● LED alarm● Alarm threshold● Low battery indication● Alarm mode setup● Auto power off● USB interface● ℃/℉ selectionSKU: n/a -
DC Power Supplies
YIHUA 605D DC Power Supply
YH-605D communication maintenance power supply
605D communication maintenance power supply is a single line output of stabilized high accuracy
DC stabilized power supply. The output voltage and current can be adjusted continuously within
the rated range. Double digital display shows output voltage and current independently. Several
protection functions include current limitation, voltage reduction, short circuit protection, over-
temperature protection, etc.
The design is applied to production line of the plant, maintenance, laboratories and is also
a necessary device for the communication industry.
SKU: n/a -
LCR Meter
UT620 Series Digital Micro Ohm Meters
UT620 series are used to measure DC low resistance through 4-wire method. Some of its features are: Comparison function to determine if the device is in good condition, unknown wire length calculation (FT/M); two-way data transmission by USB interface; built-in rechargeable lithium battery. UT620 can be used in narrow space for on-site troubleshooting, such as metal coating resistance/motor and small transformer winding resistance measurement, earth system joints/welding points/power distribution cabinet bus and lead connection inspection and more.
SKU: UN62B0TUOM -
Plier and Wire Strippers, Tools and Hardware
JM-CT4-12 Electrician Wire Stripping Tool
Features:
- Standard specs, form-ground, knife-type blades for accuracy, easy stripping without nicking insulation.
- Built-in wire cutter and looping holes.
- Convenient plier nose and sharp edge for pulling out the wire easily without damaging the wire cores.
- Spring-loaded automatic opening
- Sharp serrated edges in a plier style for wire pulls and loops.
SKU: n/a -
Tool Kits
JM-8133 23 in 1 Screwdriver Ratchet Hand-tools
Features:
- New 23-in-1 interchangeable precise manual tool set.
- Professional portable hardware tools with perfect weight and compact design for easy implementation.
- Comes with an accessory box for small components.
- More bits of cr-v are very suitable for deep holes.
- Non-slip hard shaft provides more comfort and convenience.
- For repair laptops, mobile devices.
SKU: n/a
There are no reviews yet.